G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » THUMPer Forum » Buell Blast Thumper Knowledge Vault » BodyParts-Seats, Fairings,Lights,Pegs,Rear Sets, Bars, Grips, Clip ons, Mods » OK, changed bars..now what? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Leashrn
Posted on Monday, April 28, 2008 - 02:48 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I changed to pretty flat drag bars on my (now my daughters - whole other post - as I will never sleep again and have developed an ulcer) now when she does very low speed /tight turns, the starter button hits the tank, and she broke the idle cable adjuster threads. So now the wire cable can be seen and I guess is at risk for fraying and breaking.
One more item. The run/off switch and starter switch module's nipple that keeps it from spinning must have broke off (as I have heard they do - more than likely while doing these tight turns) and no amount of tightening has stabilized the module and it spins pretty freely.
Should I change the bars again, or is there some way around this? And the clutch is a bear - the cable now binds pretty badly. We did lube the cable and adjusted the lever.
Any thoughts?
Alisha
Top of pagePrevious messageNext messageBottom of page Link to this message

Ezblast
Posted on Monday, April 28, 2008 - 04:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Arggghhhh - ye pirates always find a way to goof up a cannon ball!
- lol - flat drag bars will do that - there is no clearance - why we suggest superbike or clubman bars -
You can tape the throttle cables to each other to protect from further harm. Wrap the bar where the controlls are going to go a few times with duct tape and they will stay put - thats what most folks do anyway. Try rerouting the clutch cable a bit. That should have you back on the hi seas shortly.
EZ
Top of pagePrevious messageNext messageBottom of page Link to this message

Urbanmello
Posted on Monday, April 28, 2008 - 05:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I went through this same thing with my blast. It had Clamp-ons when I bought it they looked total cool.

I used a plastic hanger to make a proto-type handlebar and found the lowest bar I could use was 4" Rise. The stock bars are 6" rise
I ended up buying a pair of Medium 4"rise bars. ( Renthal, made in UK, $65.00, Light weight Alloy, Colors available )
As you describe it, the restriction in motion caused by a flat or no rise bar dosent work well on the Blast. The biggest problem for me was not being able to lock the front end when I left my bike. I suspect you cannot lock the steering on yours. You can move the controls around a little but they will still hit the tank.
Watch you thumbs!

b


My clutch cable dosen't bind anymore with 4" rise bars and the ride position is awsome ! !
Top of pagePrevious messageNext messageBottom of page Link to this message

Leashrn
Posted on Monday, April 28, 2008 - 07:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks guys!
Will try some higher rise bars. At least the bars I bought were only $14.
This board is the greatest resource and folks on it are even greater!
Oh yes, I'll give the duct tape a try - meshes great with my philosophy: anything can be fixed with the 3 items in my tool box. 1)duct tape. 2)hammer. 3) zip ties.
Kinda of along the line of my "keyboard"
AAARRRRGGGGG mateys
Alisha

(Message edited by leashrn on April 28, 2008)
Top of pagePrevious messageNext messageBottom of page Link to this message

Ezblast
Posted on Monday, April 28, 2008 - 07:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

20 bucks at Chapperall motersports - link in links section - for superbike bars that fit - in either chrome or black.
EZ
Top of pagePrevious messageNext messageBottom of page Link to this message

Xgecko
Posted on Tuesday, April 29, 2008 - 11:06 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Also Moose Racing ATV bars work just find not as much pull back as Superbike bars (read as more agressive)Also $14 at your local HonKwakazumaha shop....locking your tree is no issue
Top of pagePrevious messageNext messageBottom of page Link to this message

Leashrn
Posted on Wednesday, May 07, 2008 - 09:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks guys,
Got another set of bars from Chapparal with a little bit higher rise and so far so good. New cable and modual in place too.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fast1075
Posted on Saturday, May 10, 2008 - 09:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Today I installed a set of the superbike bars...I really like the feel, but the switches hit the tank with the bar angle where it should be to be comfortable...no biggie...I will get a set just a fuzz taller...beats the stockers that look like they belong on a "My Little Pony" bicycle..

The guys at Chaparrel did a great job of getting my parts out to me!! I would have to say great vendor!!! : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Fast1075
Posted on Tuesday, May 20, 2008 - 10:39 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Update...I ordered a set of GP bars...a little taller than the superbike bars...the switches hit the tank with them also UNLESS I have the bars jacked up at a rediculous angle.

I am determined to have a nice set of bars AND to clear the tank cover without damage AND to be able to lock the steering.

Last night I took a long hard look at what I have to work with....I have decided that there is quite a bit more steering angle than needed...almost as much as needed on a trials bike LOL!!! Certainly more than I need for street use...(and if it was a dragbike, an illegal amount!)...What I intend to do is rework the fork stop on the steering head to limit turning angle to where the superbike bars will not hit while adjusted to a comfortable angle....then I will modify the lock notch in the top of the neck so the lock will work at the new reduced angle.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fast1075
Posted on Friday, May 23, 2008 - 09:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The superbike bars are back on...I fabbed and welded a new steering stop on the neck..the bars when properly adjusted for best comfort do not hit the tank now..the bike has plenty of steering travel...tonite I will notch the head lock so it works...

I guess some bikes came from the factory with more or less steering travel than others...thats the only explaination I can think of where low bars fit one bike and not another....in any case, it's an easy fix if you have a MIG welder and a good die grinder ; )
Top of pagePrevious messageNext messageBottom of page Link to this message

Rockstarblast1
Posted on Tuesday, June 24, 2008 - 09:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have the same problem with my clubmans I just deal with it tho. Only part that's anoying is if I'm trying to move my bike around in a tight place, I sometime hit the horn button on the tank and startle people lol
Top of pagePrevious messageNext messageBottom of page Link to this message

Uberblast
Posted on Wednesday, July 23, 2008 - 06:02 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have clubmans on mine too - had same problem, so I put on risers that go up 1.5" and back about 1" - has full motion now and I can lock the bars :-)
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration