G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through January 10, 2015 » Is there any difference between 99 and 2000 X-1 ECM « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Moto619
Posted on Monday, December 15, 2014 - 09:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I am looking for a ECM for my 99 X-1 there is one on ebay that is off a 2000 x-1 are they interchangeable?
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluzm2
Posted on Monday, December 15, 2014 - 11:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Don't bother with a stock ECM. Get the "Race" version or a flashed stocker. The stock ECM was really lean and ran like crap.
Top of pagePrevious messageNext messageBottom of page Link to this message

Screamer
Posted on Tuesday, December 16, 2014 - 12:01 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Moto619,
Interchangeable - somewhat...
You can put a later ECM on an early DDFI system like you're describing, but shouldn't (can - but shouldn't) put an early ECM on a late system (due to temp sensor location).
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, December 16, 2014 - 10:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The very first 1999 computers had issues but were reflashed with new fuel curves to be the same as 2000.

As said above, don't bother- get the race ECU.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hootowl
Posted on Tuesday, December 16, 2014 - 10:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Get the 2000 ECM from ebay and flash it with the race map using ecmspy. Will work just fine.
Top of pagePrevious messageNext messageBottom of page Link to this message

Moto619
Posted on Tuesday, December 16, 2014 - 01:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I will probably go with the race ECM. I tried ecmspy on this ecm and it never worked again.
Top of pagePrevious messageNext messageBottom of page Link to this message

Screamer
Posted on Tuesday, December 16, 2014 - 11:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

There were five calibration improvements to the original Race ECM calibration.
Later is better.
In the race ECM , look for calibration label numbers ending in - or with a "4J" or "3K" imbedded in the number (if the labels are still in place).
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Wednesday, December 17, 2014 - 08:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I know some folks here had issues trying to load ECM maps from newer 2000 or 2001 X1 onto a 1999 X1 ECM but theoretically you should be able to swap the entire ECM unit assuming its data is not corrupted. What is the production date of your bike?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hootowl
Posted on Wednesday, December 17, 2014 - 09:25 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I think you have to update the code in the 99 ECM before you can load the later maps. Mine was flashed by a dealer and then updated to a newer map. I have since bought a race ECM, and given the stock unit to a badwebber whom shall remain nameless (because I forgot who I gave it to).
Top of pagePrevious messageNext messageBottom of page Link to this message

Moto619
Posted on Thursday, December 18, 2014 - 06:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

How do I find the production date of my Bike? Where is a good place to buy race ECM's?
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Thursday, December 18, 2014 - 08:18 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Production date is printed on a small sticker/label on the frame near the clutch cable behind the triple tree.
Top of pagePrevious messageNext messageBottom of page Link to this message

Firemanjim
Posted on Friday, December 19, 2014 - 03:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Just remap yours with ECM-Spy, way cheaper that a "race " ecu. Probably have good map here I can send you.
Top of pagePrevious messageNext messageBottom of page Link to this message

Kalali
Posted on Saturday, December 20, 2014 - 08:54 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Moto, what's the code on the label on the ECM? It should read something like this US15JA120, etc. As Fireman mentioned, you could try loading a Race map using ECMSpy if your firmware doesn't reject the map. What intake/exhaust set up do you have on the bike?
Top of pagePrevious messageNext messageBottom of page Link to this message

Moto619
Posted on Sunday, December 21, 2014 - 06:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The production date of the bike is September 1998. The code is US06Go0__ (could not read the last few digits). There was also these codes: BFI US0 and NO306_K_98240.

Here is the whole story with this bike for the past few years it has been running bad. It lurches when the throttle is kept steady. Runs perfect at full throttle.

Based upon a thread I started here I bought Ecmspy and performed a TPS reset. This did not change anything. I then changed the mapping. Following this the bike would not run / multiple error codes appeared. It will now only start/ run momentarily when the starter button is depressed. I tried to reinstall the original map no luck.

I talked to another member here that has a 99 X1 he had the same exact thing happen to him. He thinks there is a glitch in the ecmspy with only the 99 x-1.

That is where I am at now and thus my idea was just buy a race ECM.
Top of pagePrevious messageNext messageBottom of page Link to this message

Screamer
Posted on Monday, December 22, 2014 - 12:13 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

06G is the last revision of the original (1999 version) firmware. If your bike was a September 1998 build, it was built with a " 02G" calibration. Having an 06G label means the bike either had the "B017" calibration upgrade (released in May of 1999) or the ECM was replaced at some point.
I'm not too certain if ECMspy is compatible with all three versions of the firmware. I'm sure someone else here will know.
Top of pagePrevious messageNext messageBottom of page Link to this message

Moto619
Posted on Monday, January 05, 2015 - 01:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Any advise from someone with a 99 X-1 ?

Should I get a Race ECM and if so any ideas where I can get one?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hootowl
Posted on Monday, January 05, 2015 - 02:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

http://www.ebay.com/itm/Buell-RACE-USE-ONLY-ECM-mo dule-X1-S3-1999-2002-/251781586084

Spendy, but that's what they cost new. Seller's market.
Top of pagePrevious messageNext messageBottom of page Link to this message

Moto619
Posted on Monday, January 05, 2015 - 06:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks just bought it. So do I have to do anything special before I install it or just plug it in.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hootowl
Posted on Monday, January 05, 2015 - 07:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Plug it in. But then you need to do a tps reset. The new ecm needs to know the voltage offset that is unique to your throttle position sensor.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration