G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Cr low bars on xbs lightening « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Mxer83
Posted on Monday, January 23, 2006 - 02:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

hey guys any tips on mounting those cr low bars on a lightening? there are 2 holes in the stock bars to position the electric controls, looks hard to find the right spot to drill, or do you just grind off the plastic nibs on the inside of the controls?, any input appreciated
Top of pagePrevious messageNext messageBottom of page Link to this message

Fullpower
Posted on Monday, January 23, 2006 - 02:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

marked and drilled mine, not difficult.
Top of pagePrevious messageNext messageBottom of page Link to this message

Odie
Posted on Monday, January 23, 2006 - 02:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Mxer83- I cut the nubs off. Works just fine and much easier.....
Top of pagePrevious messageNext messageBottom of page Link to this message

Dana P.
Posted on Monday, January 23, 2006 - 02:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Cut mine off as well they don't move without them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Typeone
Posted on Monday, January 23, 2006 - 04:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I cut the nubs off too. Mine have moved a little but i think it was after the dealer loosened the controls. Just keep 'em way snug and you should be fine. I remember someone wrapped a little electrical tape around the bar to hold them in place, thats prob what I'll do for this season.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ratyson
Posted on Monday, January 23, 2006 - 05:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Didn't have to cut the nubs off of mine.
I got my Xroads bars used. They had little notches drilled in them to accommodate the nubs.
I am guessing that they are not drilled this way from the factory?
Top of pagePrevious messageNext messageBottom of page Link to this message

Gentleman_jon
Posted on Monday, January 23, 2006 - 07:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

One way around the nubs hole problem is to wrap some masking tape around the bars where the nubs will be. Then temporarily install the controls where you want them. The nubs will mark the tape. Drill where the marks are.
Top of pagePrevious messageNext messageBottom of page Link to this message

Saintly
Posted on Monday, January 23, 2006 - 08:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)



Hey G.J. can I have your autograph? I seen this on the BUELL website, and I figure now that you're famous I'd better get in line!
Top of pagePrevious messageNext messageBottom of page Link to this message

Gentleman_jon
Posted on Tuesday, January 24, 2006 - 05:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Fritz,
I'll be signing bikes at the March Badness in Suches Georgia, last weekend in March.

Hope you are going to be there. It is going to be everything that the Apalachian Adventure was supposed to be, but wasn't.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tommy_k
Posted on Tuesday, January 24, 2006 - 10:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I second what Jon said.

A couple wraps of masking tape, then just "squeeze" the controls when you have them in place. Makes a really nice imprint to drill. Easy piece of mind...

Tom
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration