G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through March 17, 2005 » Buell and Bosch o2 sensor! « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnk3
Posted on Sunday, March 13, 2005 - 04:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

saw that too when I out my new NEW force pipe on. Are all o2 sensors created equal?
Top of pagePrevious messageNext messageBottom of page Link to this message

Mbsween
Posted on Sunday, March 13, 2005 - 04:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Check the KV for the Fi section, this is a direct replacement for the X1 also. I've been using them for the past 20K
Top of pagePrevious messageNext messageBottom of page Link to this message

Cataract2
Posted on Sunday, March 13, 2005 - 06:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

If this is true then I will consider it when it's time. Anything to save a few bucks.
Top of pagePrevious messageNext messageBottom of page Link to this message

New12r
Posted on Monday, March 14, 2005 - 09:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Not all oxygen sensors are the same but there are only a handfull of different ones. These are very basic o2 sensors, single wire(duh) and only read a lean condition. I would love for Buell to add four wire oxygen sensors with one on each cylinder, think of the tuning.
Top of pagePrevious messageNext messageBottom of page Link to this message

Enduro261
Posted on Monday, March 14, 2005 - 12:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

What's the verdict? Same or not the same. I would like to put a new O2 sensor in since I have my header off right now
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnk3
Posted on Monday, March 14, 2005 - 01:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

same. I just picked one up and installed it today.
Top of pagePrevious messageNext messageBottom of page Link to this message

Spatten1
Posted on Monday, March 14, 2005 - 02:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

A basic three wire sensor would work better, as they output the same voltage range, the only difference is that the three wire has a heater so it gets up to temp. much quicker. You would have to use an ignition switched power source for the heating element.
If anyone remembers the early 90's V8 GMs went into open loop on long idles because the one wire O2 sensors were too far from the head and they cooled off. Some people retro fitted three wire sensors to solve the problem.
Top of pagePrevious messageNext messageBottom of page Link to this message

Noface
Posted on Tuesday, March 15, 2005 - 04:18 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

same sensor. I've run one on my 9R for quite some time.

I now have a PCIII w/heated O2 with a Force system. I also got the heated O2 at AutoZone for condsiderable less than what DynoJet get's for theirs...
Top of pagePrevious messageNext messageBottom of page Link to this message

Johnk3
Posted on Tuesday, March 15, 2005 - 07:12 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

noface, part number?
Top of pagePrevious messageNext messageBottom of page Link to this message

Noface
Posted on Tuesday, March 15, 2005 - 08:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Johnk3,

15716 Bosch is what you want for the heated O2, or DynoJet High Performance equivalent.

The above part number is correct for the factory replacement.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Wednesday, May 12, 2010 - 05:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Note I moved the parent post for this to the knowledge vault...

http://www.badweatherbikers.com/cgibin/discus/show .cgi?tpc=3842&post=401397#POST401397
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration