G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through June 05, 2014 » Throttle cables? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Dwilson357
Posted on Tuesday, April 15, 2014 - 08:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Does anyone know of any alternatives for the throttle cables?
50 a pop does not sit well with me!!!
That seems insane for what they are lol.

I did some searching but haven't had any luck there so chances are this is a dead end.

Thanks
Dave W.
Top of pagePrevious messageNext messageBottom of page Link to this message

Pash
Posted on Thursday, April 24, 2014 - 04:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Why don't you fit new inners?
Top of pagePrevious messageNext messageBottom of page Link to this message

Nillaice
Posted on Thursday, April 24, 2014 - 07:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I used some new cabling and smelted on my own barrel ends. Flanders can sell you everything you'll need, but I had better and stronger results using some 'aluma-weld' for the barrel ends instead of lead, silver and/or tin solder.

I posted this all in a thread last year or so ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Nillaice
Posted on Friday, April 25, 2014 - 01:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yup

http://www.badweatherbikers.com/buell/messages/142 838/711543.html?1368109734
Top of pagePrevious messageNext messageBottom of page Link to this message

Ducbsa
Posted on Friday, April 25, 2014 - 07:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Nilla, did you spread out the wires before final soldering? That makes for a stronger joint.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ducbsa
Posted on Friday, April 25, 2014 - 07:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Here is a page from a Jeff Clew book:


Cable Fab
Top of pagePrevious messageNext messageBottom of page Link to this message

Dwilson357
Posted on Wednesday, April 30, 2014 - 11:10 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have a couple of those clamp type ends.
I'm not against using them on the throttle body side.
Right now i have to figure out what size wire..I would guess its 1.5mm but if someone could verify for me.
I would check myself but it will be raining here the next few days and I'm stored outside right now.
What diameters are the ends as well?
I noticed the posted thread for making your own end didn't have alot of specifics.
Again I'd normally just go take a measurement myself but I don't own any snorkeling gear.

Thanks,
fellas.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brother_in_buells
Posted on Wednesday, April 30, 2014 - 02:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have to replace both of the inner cables from my 04 xb 12s at the moment to.
the inner cable is 1,25 mm
and the barrels are 6mm in diameter.

i would use the clamp type only for a road repair or so ,but not all the time!
Top of pagePrevious messageNext messageBottom of page Link to this message

Dwilson357
Posted on Wednesday, April 30, 2014 - 06:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Wonderful thanks alot! I will some stuff on order!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration