G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Anyone removed an XB engine? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Dr_greg
Posted on Wednesday, May 12, 2010 - 09:14 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

My '06 Uly has developed a bearing noise in the transmission, and I'm afraid it'll die on the way to Homecoming.

So...I'm thinking of swapping engines with my other '06 Uly "parts bike" (totaled on a deer at 55,000 miles).

Has anyone removed an XB engine? I've had the heads and cylinders off, so I'm familiar with wrenching on these things.

I'm mainly concerned about any unusual tools, tricks, tips, etc. that might save me some headaches.

Thanks for any help.

--Doc
Top of pagePrevious messageNext messageBottom of page Link to this message

Whitetrashxb
Posted on Wednesday, May 12, 2010 - 09:34 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

mine is sitting on the workbench as we speak (see Case splitting thread), removing the Xb motor is pretty simple and straight forward, tearing it down to every last nut and bolt a little more time consuming (for me). Use the manual and you cant go wrong.
Top of pagePrevious messageNext messageBottom of page Link to this message

Rocketsprink
Posted on Wednesday, May 12, 2010 - 08:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

what he said. I've swapped engines in my race bike in a few hours by myself. As long as you have a service manual. No special tools required.
Top of pagePrevious messageNext messageBottom of page Link to this message

Coolice
Posted on Wednesday, May 12, 2010 - 09:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Dr Greg- I build all our race bikes, I hang the frame from garage ceiling with tiedowns, unbolt the engine with the service manual as a guide for torque values and sequences. The swingarm is attached to the engine so you could just swap the engine/swingarm if you have your other bike there. That would be very quick to do, lift the frame off and exchange them.
Top of pagePrevious messageNext messageBottom of page Link to this message

No_rice
Posted on Thursday, May 13, 2010 - 11:58 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

i assembled this in a few hours, a few years ago after hauling it across the country to my house in boxes...









its alot easier then most people think, although im not looking forward to the day i rip the motor out of one of my 1125's lol

the fact that you will have 2 to look at always helps.
Top of pagePrevious messageNext messageBottom of page Link to this message

B00stzx3
Posted on Thursday, May 13, 2010 - 01:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Noice!!!! Bookmarked for my future 12R swap...someday haha.
Top of pagePrevious messageNext messageBottom of page Link to this message

Firebolt32
Posted on Thursday, May 13, 2010 - 06:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

He has ice B00...just no rice!


Wouldn't it have been less time consuming by just trailering it? Damn dude!
Top of pagePrevious messageNext messageBottom of page Link to this message

U4euh
Posted on Thursday, May 13, 2010 - 10:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You can do it in a day easily! But it will go much faster if you have a second set of hands to help you lift.You could chock the front tire and place a jck under the motor. Dis assemble from the rear wheel forward, disconnect the mounts and wires have buddy lift the frame as you remove the motor.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration