Author |
Message |
Nm5150
| Posted on Wednesday, March 21, 2018 - 01:15 pm: |
|
Where can I find some injectors for a 2000 X1 or how can I clean mine? Thanks. |
Mhlunsford
| Posted on Wednesday, March 21, 2018 - 03:13 pm: |
|
supposedly Ford uses the same injectors |
Buelliedan
| Posted on Wednesday, March 21, 2018 - 03:14 pm: |
|
I don't know where to find injectors but if you are interested I have a complete throttle body with injectors and sensors still attached that I will sell for $125 plus shipping. It came off a good running 2000 X1 that was crashed with only 8,000 miles sales@nrhsperformance.com |
Hootowl
| Posted on Wednesday, March 21, 2018 - 03:17 pm: |
|
Injector cleaning service. https://www.injectorrx.com/ |
Hootowl
| Posted on Wednesday, March 21, 2018 - 05:32 pm: |
|
You can usually find used injectors on ebay too, though there's no guarantee you won't have to have those cleaned after you buy them. But the Tuber injectors are Ford parts, which means there's very likely many manufactures to choose from. If you search badweb's knowledge vault, you'll likely find a part number. |
Nm5150
| Posted on Wednesday, March 21, 2018 - 08:51 pm: |
|
Thanks for the replies and buelliedan I might take you up on that but I have another question now. The bike has a race ecm,exhaust and air filter. Should it have different injectors than stock? |
Harleyelf
| Posted on Wednesday, March 21, 2018 - 09:28 pm: |
|
No, the race kit did not come with new injectors. |
Firemanjim
| Posted on Sunday, March 25, 2018 - 01:52 am: |
|
If you were closer, I have an injector cleaning and testing machine----0r connect them to a 9 volt battery and spray carb cleaner through in both directions, then compressed air. |
Nm5150
| Posted on Sunday, April 01, 2018 - 07:41 pm: |
|
Thanks Mr.Fireman. As a temporary fix we used some Lucas injector cleaner just to see if we could get her to fire. I installed a new fuel pump and a race ECM and it smoothed out after a little bit. Went for a short ride and this thing is a beast. |
Steveford
| Posted on Wednesday, April 04, 2018 - 08:19 pm: |
|
No cross reference for these? I looked but no luck. |
Lasbuell
| Posted on Thursday, April 05, 2018 - 08:37 am: |
|
Someone had posted this on here a while ago. "I’m new to this page but have owned Buells since 2001 I have found this very helpful Cross references to compatible parts fuel injector for OEM 29533-99Y....Bosch P/N: 0280 150 784" |
Steveford
| Posted on Thursday, April 05, 2018 - 06:42 pm: |
|
Thanks! |
Lasbuell
| Posted on Friday, April 06, 2018 - 08:40 am: |
|
Here is the list he posted. I’m new to this page but have owned Buells since 2001 I have found this very helpful Cross references to compatible parts Oil filters ACDelco # UPF1233 Amsoil SDF10, EA009, EA010 (1/2â€�longer=more oil) Bosch # 3311 Car Quest 85394 Champion # C138 Fram # PH4967 HD # 63806-004 or 00y? HiFloFiltro #HF177 K&N # hp-1003, KN-177 Mighty # m4477 Napa # 1394 Mobil 1 # M1-103 Motorcraft # FL836 Penzoil # pz39 Purolator # L14476 STP # S4967 Valvoline # vo40 Wal-Mart Super Tech # ST49ST4967 o2 sensor GM=25162693 NTK= 21002 Airtex= 553071 Bosch= 12014 Denso= 234-1001 Walker= 250-21001 SNG= SN1-15 Union Sangyo[OEM Toyota Mfg]#C-170. Wheel bearings: SKF6006-2RS (Rear), SKF6005-2RS (Front) IAT - 97 Ford F-150 4.6L TPS sensor: Duralast #TPS213 ('93 Mustang) fuel pump for a 03 musntang V6, part number E2366 at autozone XB fuel pumps are made by Walbro and are model #521 replacement starter # HARLEY DAVIDSON 31390-91, 31390-91A, 31390-91B, 31390-86, 31533-81, 31391-91, 31391-91A NIPPONDENSO: 128000-8450, 128000-8451 a new P/N for you guys doing the front end conversions on your bikes...headlight harness connectors: male connector...P/N: 73154-96WE female connector...P/N: 73104-96BK AIRTEX Part # 5S5022 (07+ TPS) Standard motor products TH317 (07+ TPS) BECK/ARNLEY Part # 1580864 (07+ TPS) Duralast TPS4129 (07+ TPS) fuel pump alternatives: Manufacturer Part Number Walbro Part Number AC Delco EP274 521 Delphi 25337782 521 Delphi FE0052 521 Ford E5ZZ-9A407-A 521 General Motors 25116975 521 Hella H75010041 521 2009 XB12R. Fuel pump strainer: Airtex FS213 Fuel pump filter: Puralator F29160 Alternative body plastics and battery tray hardware: 1/4-20 x 3/8" and 1/4-20 x 5/8"..........3/8" and 5/8" thread length not including the shoulder, shoulder diameter is 5/16", height 1/4". T-27 security bit needed. 18-8 Stainless Steel. Grainger: Shoulder screws item #'s...5MA50 5MA5I Non-shoulder screws ...5MA42 5MA43 fuel injector: for OEM 29533-99Y....Bosch P/N: 0280 150 784 |
Azrael_cervale
| Posted on Saturday, April 14, 2018 - 10:09 am: |
|
IF you want to verify injectors you can do that with a 12v source and some aerosol spray cleaner. I watched a video on youtube and it's fairly simple. I'm sure it's not as good of a clean as sending them out or new ones, but you can check to see if they are truely clogged/not functioning if this is a troubleshooting step. https://www.youtube.com/watch?v=7aT4S1lIBAY |
Steveford
| Posted on Saturday, April 14, 2018 - 08:13 pm: |
|
I've been following this with interest as my X1W started bucking and carrying on and running like crap. I wonder if it's going to pop a belt kind of running. Luckily, some Marvel Mystery Oil and two gallons of fresh gas got it running normally. That bike is so much fun to ride and the local Harley bagger bad boys don't know what the hell to make of it when it starts up! They hear the exhaust noise but where is it coming from??? |
Mighty_mouse
| Posted on Sunday, April 15, 2018 - 10:04 pm: |
|
Last summer I had a coworker working with me in the garage (older about 57) and I was making fun of this turd flying down the road in high rpm on a boulevard with cut exhaust. I made the comment about how everybody wants to sound like a Harley. Jim says "did you ever hear yours from the back, it sounds like a Harley". I said "yea, I get that a lot"....lol |
|