Author |
Message |
Percyco
| Posted on Wednesday, February 22, 2006 - 04:21 pm: |
|
Just whipped up a set of XB axle sliders for pocket change, maybe a fellow cheapskate like myself would like my recipe . Hope I never have to use them ! New Skateboard wheels found on Ebay.........$8.00 Threaded 5/16 rod, acorn nuts and washers...$6.00 Rubber hose to slide over threaded rod to protect inside of axle......................$0.50 Protected aluminum Buell parts........priceless !
|
Jimduncan69
| Posted on Wednesday, February 22, 2006 - 04:35 pm: |
|
what a great idea! |
Dmextreme
| Posted on Wednesday, February 22, 2006 - 04:52 pm: |
|
nice.. this could be interesting.. bravo! (Message edited by dmextreme on February 22, 2006) |
Midknyte
| Posted on Wednesday, February 22, 2006 - 05:04 pm: |
|
You're not the first, but nice job. |
Percyco
| Posted on Wednesday, February 22, 2006 - 05:32 pm: |
|
Didn't figure I was.....those "Axle Bobbins" that are on Ebay and sold by a fellow in the UK look pretty similar. PC |
Holling
| Posted on Wednesday, February 22, 2006 - 05:35 pm: |
|
Don't skateboard wheels tend to grab the pavement rather than slide? Could cause bike to flip. |
Wahmbush
| Posted on Wednesday, February 22, 2006 - 06:00 pm: |
|
Holling....thought and heard the same thing....any info to back it up? |
Gentleman_jon
| Posted on Wednesday, February 22, 2006 - 06:04 pm: |
|
Thats fine if you have a black bike However, those brothers who sport coloured plastic might want to consider a skateboard wheel with a matching center, such as these Recta's spotted in Sag Harbor PS: Actual crash experience, (not by your correspondent), indicate the the skateboard wheels rotate, and do NOT dig in. |
Moonrunrs
| Posted on Wednesday, February 22, 2006 - 07:59 pm: |
|
Another great idea from the badweb! |
Moonrunrs
| Posted on Wednesday, February 22, 2006 - 08:04 pm: |
|
What size skateboard wheels are those, 50mm? Do you know? |
Percyco
| Posted on Wednesday, February 22, 2006 - 08:12 pm: |
|
52mm....They are very hard....probably why they were so cheap compared to the brand name wheels. I dont think they would dig in anymore than a set of aluminum sliders. More than likely they would just wear away. My .02 PC |
Moonrunrs
| Posted on Wednesday, February 22, 2006 - 08:29 pm: |
|
Percyco, thanks, this is totally cool. I think I'm going to put these on my 'bolt too. I found the wheels you used on Ebay, and think I'm going to order a blue pair to match my body work as closely as possible. Last question: what type of rubber hose did you use to protect the inside of the wheel axle? did you have a hard time fitting it in there? |
Randlepmcmurphy
| Posted on Wednesday, February 22, 2006 - 09:15 pm: |
|
This idea is great just a couple questions? How long did you cut your rods and did you put anything under the wheels to protect the finish? |
Percyco
| Posted on Wednesday, February 22, 2006 - 10:11 pm: |
|
I used the clear plastic hose you can get at any hardware store. I didn't measure the rod , I mounted a wheel to one side then slid it through the axle. Then I slipped the other wheel over the other side. I marked it, removed it and cut it off. I used red locktight and turned the nuts until they bottomed. I didn't put anything behind the wheels because I figured that the powder coat was much tougher than the hard rubber wheels. PC |
T9r
| Posted on Thursday, February 23, 2006 - 09:11 am: |
|
I did the same thing, looks very similar and got some of the same questions thrown at me about digging in. http://www.badweatherbikers.com/buell/messages/32777/148545.html I used couplers at the ends of the rod on mine, so it made it easier and I didn't have to be precise on a specific length rod. I also did not put anything under the wheels because it pushes up against the axle on one side. I did drill tiny drain holes thru the wheels so I didn't trap too much moisture in the axle. I also had lubricated the threaded rod with axle grease to keep it from rusting, the tube thing is a good idea as well. |
Diablobrian
| Posted on Thursday, February 23, 2006 - 11:11 am: |
|
you can get pieces of delrin fairly cheaply on ebay. a 1 1/2 or 2" diameter piece a foot long would make enough for 2 bikes pretty easily. Delrin is the material most comercial sliders are made out of. All you need for the project would be a saw, a file, and a drill. (If you don't have a lathe and mill) For hardware all-thread rod is available at any hardware store. If you want to be slick epoxy a nylock nut into the sliders. Inserted from the outside of course, so that if the epoxy fails the slider does not fall off. should make (re)assembly easier if you (red) locktite the all thread into one end. I have a piece of 2" Delrin and I'll be making a pair for my front axle soon. I'll post pics when I do. FWIW even hard skateboard wheels are designed to grip pavement. while less than rubber, it will still have more grip than metal or delrin in the same conditions and could possibly bite and cause greater damage during a low side accident. Not saying it will, just that it could. |
Sgthigg
| Posted on Thursday, February 23, 2006 - 11:22 am: |
|
Cool idea. Skate board wheels are rated in levels of hardness(100a are the hardest i think there is a 101 also). They are pretty much like rocks when they get that hard. The Harder ones will definetly slide better than softer ones. Higher the rating less grip, lower the rating more grip. I would definetly go with the hardest one I could find if I was to do this. |
Stealthxb
| Posted on Thursday, February 23, 2006 - 11:23 am: |
|
Skateboard wheels slide just fine! Gentleman_jon... I believe you meant Ricta |
Gearhead998
| Posted on Thursday, February 23, 2006 - 01:35 pm: |
|
Did you guys use bearings in the skate wheels or is there enough of a lip for a washer to catch. I think this is a great idea, as I can't afford aluminum sliders. Just wondering how it would hold up. |
Percyco
| Posted on Thursday, February 23, 2006 - 04:07 pm: |
|
No bearings in mine, just washers. |
Gearhead998
| Posted on Thursday, February 23, 2006 - 04:20 pm: |
|
sweet, thanks |
Roly
| Posted on Thursday, February 23, 2006 - 05:30 pm: |
|
hi funny those skateboard wheels ,i got them too ,been on for a year ,45mm long on threaded bar and thick washers, the xtra 5mm just in case they get grounded,would put longer ones on if i could of got some. |
Roly
| Posted on Thursday, February 23, 2006 - 05:42 pm: |
|
bike with skateboard wheels |
Percyco
| Posted on Thursday, February 23, 2006 - 06:11 pm: |
|
Roly, Is that another wheel above the front engine cyl. ? |
Bueller999
| Posted on Thursday, February 23, 2006 - 08:53 pm: |
|
Thats an LSL slider |
Buelltroll
| Posted on Friday, February 24, 2006 - 12:20 am: |
|
This idea is AT LEAST 3 years old. I did these in the summer of 03 and by the summer of 04 they were faded.
|
Buellistic
| Posted on Sunday, March 19, 2006 - 05:27 pm: |
|
The SKATEBOARD WHEELS like the ones the "LORDS OF DOGTOWN" used are faster wheels too !!! |