G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » Buell RACING & More » Racing - Drag Racing » Turbo a XB12 or a 1125? « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through January 26, 2015Blownharley30 01-26-15  08:19 am
Archive through December 30, 2012Firemanjim30 12-30-12  09:45 pm
Archive through July 15, 2012Hybridmomentspass30 07-15-12  11:13 pm
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Battyone
Posted on Monday, January 26, 2015 - 09:29 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'll be keeping an eye out for updates. Not the easiest turbo bike to tune, twins are notorious for being difficult under boost.

I've looked at the throttle bodies a few times. trying to figure the best way to attach a plenum. The best idea I came up with was an extended bellmouth with "O"rings on the outside diameter so the plenum body could be slipped over.

Or remove the throttle bodies and run one on the other side of the plenum?

The frame limits everything, so I've made the decision to leave more engine mods until I have made a custom frame that allows me to work on the motor without removal.

I've got a set of EFR cams, but imagine a day at the dyno trying to dial them in!!! It'd be a long expensive day!

Keep up the good work, give me a shout if you need any help with ECM tuning.
Top of pagePrevious messageNext messageBottom of page Link to this message

Blownharley
Posted on Tuesday, January 27, 2015 - 04:25 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks and I will probably need some help with the ECM!
Top of pagePrevious messageNext messageBottom of page Link to this message

Blownharley
Posted on Wednesday, June 24, 2015 - 08:45 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I needed to make the Buell street legal here in Sweden so I had to take the turbo off :-( Anyway went to the closest drag race track just to test it and have a base line. 10.82 was the best time slip during the weekend. Next time at the track will be with some extra power ; )
Top of pagePrevious messageNext messageBottom of page Link to this message

Blownharley
Posted on Thursday, June 25, 2015 - 08:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

A picture from the race


Midsummer race
Top of pagePrevious messageNext messageBottom of page Link to this message

Absurded
Posted on Thursday, June 25, 2015 - 07:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Browne Racing..120ci Turbo Vtwin..they have been 6.99 in the 1/4 mile...they design their plenums for 3 times the volume of 1 cylinder
Top of pagePrevious messageNext messageBottom of page Link to this message

Blownharley
Posted on Thursday, July 09, 2015 - 03:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Absurded, the Browne's bike is a Little bit more extreme then my bike. Anyway the purpose of the big plenum is to smoothen out the pressure pulses of the V-Twin Engine. My plenum will work OK but most likely I will develop the installation a bit more during the Winter.
Top of pagePrevious messageNext messageBottom of page Link to this message

Blownharley
Posted on Monday, August 10, 2015 - 04:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've changed the injectors on the bike and have asked for the flow rate of the Buell 1125 injectors on other places here at BWB. I got a number of 35 lbs/h but this number is not confirmed and wanted to know if anyone have flow tested the standard injector and would'nt mind sharing the flow numbers?

I'm getting Close to a dyno run and would like to get as Close as possible Before I put load on the Engine.

Thanks Peter
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration