G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Quick Board Archives » Archive through June 15, 2007 » Clutch and brake lever compatibilities? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Monday, June 11, 2007 - 09:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I had a bit of a mishap on my X1 and have replaced the bars with dirtbike bars.
I wanted to install barkbusters on there to scare yuppies but the levers are too long to fit inside.

Are there other bikes that have similar levers?
Are XB levers the same as mine?

I don't want to cut my levers. I would rather install new stubby levers.
Top of pagePrevious messageNext messageBottom of page Link to this message

Gjwinaus
Posted on Monday, June 11, 2007 - 10:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I think S3T brake levers are the same as XB brake levers at the reservoir end but the XB lever have the adjustment thingy, the XB brake lever is the same as the Busa and one of the 900 cc Kwakas, I bought mine aftermarket as a spare for Aus $35 (about US $28) as our local Buell dealer does not carry spares either, I'm sure the clutch lever would be available aftermarket as well, Hope this helps.
Top of pagePrevious messageNext messageBottom of page Link to this message

Al_lighton
Posted on Tuesday, June 12, 2007 - 10:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

NOOOOO!!!

The tuber and XB brake levers are NOT the same and are NOT interchangeable. I'd have to look at them to be sure which way is which, and I'm at home at the moment, but the "cam" that pushes on the piston is longer on one than the other. If you put the longer cam on the one that was supposed to have the shorter one, the bleed port in the MC won't uncover and the front brakes will lock up at an inopportune moment. If you do it the other way around, you just get a floppy lever.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikef5000
Posted on Tuesday, June 12, 2007 - 12:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Do you know of any Jap levers that will enterchange with tuber levers?
Top of pagePrevious messageNext messageBottom of page Link to this message

Cyclonemick
Posted on Tuesday, June 12, 2007 - 02:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I think they have some aftermarket levers for tubers on American SportBike.
(sponsor)
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, June 12, 2007 - 04:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

What I would really like is a set of stubby dirtbike levers.

I guess the thing to do is to rip them off and bring them into a japanese dealer and ask them?
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikef5000
Posted on Tuesday, June 12, 2007 - 06:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I also want stubby levers.

They're pretty low on my list of needs though.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, June 12, 2007 - 10:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I was just out screwing around in the garage... I mean doing important research.

I tore off the clutch lever from my sad old KLR250 and found that the pivot diameter was the same as Buell's but that the barrel at the end of the cable was larger for the Buell.
Well I drilled it out to match the Buell's and found that the curvature of the lever bumped into the switch cluster.

I hate to say it but it looks like the most easy/cheap thing to do here is to kill my stock levers.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, June 12, 2007 - 10:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I was just out screwing around in the garage... I mean doing important research.

I tore off the clutch lever from my sad old KLR250 and found that the pivot diameter was the same as Buell's but that the barrel at the end of the cable was larger for the Buell.
Well I drilled it out to match the Buell's and found that the curvature of the lever bumped into the switch cluster.

I hate to say it but it looks like the most easy/cheap thing to do here is to kill my stock levers.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Tuesday, June 12, 2007 - 10:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Oops. Wonder how I did that?
Top of pagePrevious messageNext messageBottom of page Link to this message

Blake
Posted on Wednesday, June 13, 2007 - 02:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Clicky on the "" to delete an errant post while it is still fresh. : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Daves
Posted on Wednesday, June 13, 2007 - 06:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Get some CRG short levers
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration