G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archives OSB 001 » Archive through April 20, 2007 » Rear pulley - Sportster vs Buell « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellboiler
Posted on Friday, April 06, 2007 - 11:23 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Can anyone educate me on how a 2001 sportster rear pulley can be machined to work on a 2001 X-1? Is the inner diameter of the pulley (near the hub) different or is the thickness of the pulley different?

Thanks,

Boiler
Top of pagePrevious messageNext messageBottom of page Link to this message

Aaomy
Posted on Friday, April 06, 2007 - 12:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

the center hole.. the large one between the mounting bolts has to be bored out larger..
Top of pagePrevious messageNext messageBottom of page Link to this message

Aaomy
Posted on Friday, April 06, 2007 - 12:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

if you look at my profile pick you can see my cut pulley. i have two more cut ones in the basement i quickly measured for you.. the center hole is 2.464 on one and 2.462 on the other. the flange on my rear rim that it slips over is 2.446. that is a buell rear rim not the pm. dont have one of those to measure.. from where the pulley buts up against the flange on the rim to where the bolts seat against there machined areas it was .335 thick.. hope these help... aaron
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellboiler
Posted on Friday, April 06, 2007 - 01:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks Aaomy,

That is the information I was looking for!

This site is the best.

Boiler
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikef5000
Posted on Friday, April 06, 2007 - 09:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Is this mod just for looks? Or is there a change in gear ratio?
Top of pagePrevious messageNext messageBottom of page Link to this message

Aaomy
Posted on Friday, April 06, 2007 - 10:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

both pulleys would be 61 tooth so just for looks or cheep repair i am guessing..
Top of pagePrevious messageNext messageBottom of page Link to this message

Firemanjim
Posted on Saturday, April 07, 2007 - 10:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Aaron,can you be more specific----
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellboiler
Posted on Saturday, April 07, 2007 - 02:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I just measured the stock pulley from my 2001 X-1 and the center hole diameter is 2.447", or slightly smaller than the ones Aaomy measured for me.

Firemanjim - the change would be for looks only. Either would be a 61-tooth pulley but I would prefer something other than the black to go with the PM wheels. Some Sportsters came with the same pulley without the paint, i.e bare castings. This would be easier to polish.

Boiler
Top of pagePrevious messageNext messageBottom of page Link to this message

Pilot
Posted on Saturday, April 07, 2007 - 08:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Jim Mate, back in the days of the X1 I fitted American gearing to mine to take advantage of letting the engine rev more at our highway speed limit of 60 mph. I ordered a sportster rear pulley and had it machined to fit the hub of the X1 as it was a cheaper item to buy than the Buell item ,the front sproket was no problem as no machining was needed,I also fitted a device that was made by a fellow Bueller that corrected the speedo readout. How you doing? Ross. The international gearing at our speed limit put the motor in a bad spot in its rev range and the bike lived better in fourth than fifth on the highway.
Top of pagePrevious messageNext messageBottom of page Link to this message

Wile_ecoyote
Posted on Saturday, April 07, 2007 - 08:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Strip the old one with a product called Aircraft Stripper. It will be a rough cast but that is easy to sand down then polish. May be a little more work but you wouldnt have to bore out anything either. Just food for thought.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bad_karma
Posted on Saturday, April 07, 2007 - 11:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

buell boiler this winter the guy that does my work pickup a rear pulley that was natural not black. I believe he got it from HD.
Joe
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration