G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through August 29, 2015 » Stock gearing « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Hybridmomentspass
Posted on Monday, August 03, 2015 - 11:35 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If running a chain, what would be the gears needed to get back to stock gearing on a S3?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hybridmomentspass
Posted on Monday, August 03, 2015 - 10:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

No one?
Top of pagePrevious messageNext messageBottom of page Link to this message

Mighty_mouse
Posted on Monday, August 03, 2015 - 11:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Go to the "sportster/buell" section on Baker drivetrain's website. Go to parts & acc, then buell chain conversion kits. They list the teeth for sprockets and the equiv for belt set ups.
Top of pagePrevious messageNext messageBottom of page Link to this message

Lakes
Posted on Tuesday, August 04, 2015 - 03:31 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I would take a guess that 22 tooth counter sprocket & 51 tooth rear wheel sprocket would be close.
If you want it taller 23 counter. But I would see how you like 22 51 first
Top of pagePrevious messageNext messageBottom of page Link to this message

Hybridmomentspass
Posted on Tuesday, August 04, 2015 - 07:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

thank you to both!
Top of pagePrevious messageNext messageBottom of page Link to this message

Hybridmomentspass
Posted on Tuesday, August 04, 2015 - 07:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ok, im on the Baker site
what is the stock ratio? Im seeing between 2.09 and 2.35

Or, I guess, what are the sprocket counts on the stock set ups?

I do appreciate both comments above!
Top of pagePrevious messageNext messageBottom of page Link to this message

Mighty_mouse
Posted on Tuesday, August 04, 2015 - 10:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Mine was a 27 front 61 rear which is 2.26. If you can't find it in your owners or service manual just mark one of the teeth on your sprockets and count them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hybridmomentspass
Posted on Tuesday, August 04, 2015 - 09:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I dont know where my stock sprockets are at the moment...
Top of pagePrevious messageNext messageBottom of page Link to this message

1313
Posted on Tuesday, August 04, 2015 - 10:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

S2 was 29 F 61 R
All other DOM (domestic) tubers were 27 F 61 R

HDI (International, i.e. Euro) bikes were typically 29 F 55 R

There might be some 'unusual cases' but as a general rule the above is pretty accurate,
1313
Top of pagePrevious messageNext messageBottom of page Link to this message

Tombo
Posted on Wednesday, August 05, 2015 - 07:16 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

1313, there was one other DOM exception, the 97 S3 also used a 29 front (changed to 27 in 98), likely left over from the S2 bin as was the initial S3 dash (which changed slightly during the 97 production run and completely changed for 98).
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration