G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through July 09, 2011 » Si lightning front motor mount » Archive through July 03, 2011 « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Friday, July 01, 2011 - 02:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I just got my frame back from powder coating, was putting it back on the engine & installing the front & rear mounts. The manual says to replace the front mount bolts, it says they are two different sizes, but mine are not. No signs anything was ever touched. I tried reusing to old bolts & one snapped, thankfully was able to pull it out of the engine with an extractor. Anyone know what is going on with this??
Top of pagePrevious messageNext messageBottom of page Link to this message

13was13
Posted on Friday, July 01, 2011 - 03:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The S1 has same length bolts. The manual says that you should leave them in place. If removed they should be replaced by new ones.
The manual describes a procedure: Loctite, torquespecs, fasten-loosen-fasten.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Friday, July 01, 2011 - 03:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The bolts are 7/16x2-3/4"-14 thread, grade 12.
Head of oem bolts should be stamped F911.

Replacements are pricey($20+) but worth it.
I wouldn't reuse the old ones.

Al should have them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Friday, July 01, 2011 - 04:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I got a pair of grade 8 bolts, think that's enough?? The old bolts had nothing on the head, so I'm guessing they were replaced at some point.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Friday, July 01, 2011 - 05:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I got a pair of grade 8 bolts, think that's enough?

NO

About the only bolt that will survive that service is the OE bolt, several have tried all sorts of concoctions and whatzits

what Buell used works best if properly installed

some other points, the clamping surfaces must be machined and be flat if the mount is damaged it should be replaced,

IF you have the cast mount and lost a bolt it should be tossed, get the Billet mount from American Sport Bike and some new bolts if the head clamping pad is damaged in any way, remove the head and have it repaired,

I recommend CycleRama for the work..

failure to follow the suggested may result in further damage to your bike....

YMMV}
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Friday, July 01, 2011 - 06:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ok so I'll get new bolts, but what is the proper torque?? I have found two different answers on this site
Top of pagePrevious messageNext messageBottom of page Link to this message

Guell
Posted on Friday, July 01, 2011 - 06:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have a couple of don casto bolts that are better than oem.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Friday, July 01, 2011 - 07:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Clyde:
There is an on line manual for the S1 not sure what it was,

IIRC mine are torqued to 60 ftlb

the basic
assuming that the metal parts are good and clean

the bolts get red locktite and the washers are lightly oiled, do not get the oil on the locktite

tighten to I believe tight, loosen 1 turn and re torque to spec, never disturb except to replace,

If Guell is willing to part with those bolts get them I did not mention them as they are not available any more...

you can get what should be "those" bolts from places like fastenal and they should be ok, YMMV

Guell, check C3 section u-b invited
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Friday, July 01, 2011 - 09:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

"IIRC mine are torqued to 60 ftlb"

I have found on here btwn 60ish & 75ish. The manual I have calls for btwn 100-110lb ft. Which is it?? I am afraid of stripping out the threads in the head. No where in my manual does it say anything about this special tighten, loosen, tighten torque sequence. What is going on???

OK, I need different bolts, but how do I tell the guy at fastenal what I need?? What is so special about these bolts??

Guell - Got any extras??
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Friday, July 01, 2011 - 11:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

FRONT ISOLATOR Class 101, just PM me if you want a copy ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Friday, July 01, 2011 - 11:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

7/16" bolts for Iso mount to head 60ft.lbs.

1/2" main Iso bolt 100-110ft.lbs.
Top of pagePrevious messageNext messageBottom of page Link to this message

Guell
Posted on Saturday, July 02, 2011 - 12:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I don't have any extras, ill see if I can dig up the info on them

Oldog, I should be able to make it. Did you get my pm I sent you a few weeks back?
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Saturday, July 02, 2011 - 07:20 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buellistic, Huh?? A copy of what??
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Saturday, July 02, 2011 - 08:19 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Matt:
No the @Live account is dead now I need to open a new one, I will when I get home.
keep an eye on the C3 section storm fronts
as I know what my eta home is I will post up
would love to have you over for the Cookout / Ride..

Clyde:
You can check the on line S1 manual
as that bike uses that mount too.
I have an X1 the required procedure is tight loose tight to spec, thats how the FSM says to do the deed, I would get the bolts from AL at American Sport Bike yeah they cost more
but it keeps the lights on here ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Psykick_machanik
Posted on Saturday, July 02, 2011 - 12:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

your caution is VERY warranted.
i went threw a disasterous experience with those mount bolts which resulted in a broken forward engine mount after one of the bolts snapped (while riding).
something to get right the first time.
i wouldnt recommend not putting oil on the washer tho. the torque is a "dry" torque and oil will change the stretch/torque of the bolt which could lead to overtorque or a snapped bolt.
The Horse, issue #108 May 2011 has a great article about the effects of oil on bolts effecting torque. not sure if its available on-line but worth tracking down.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Saturday, July 02, 2011 - 03:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Psykick

the Procedure from Buell calls for the washers
to be lightly oiled,

Probably to help insure some consistency in torque on the bolts
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Saturday, July 02, 2011 - 03:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

IMHO, TORQUING COMPOUND should be used on any metal to metal surface on any screw, allen screw/bolt, nuts, washers, and bolts that you are going to torque ...

"i" have only had to replace two FRONT MOTOR MOUNTS ...

FIRST one because "i" bounced of a car in 1998 and the SECOND because the second one was installed by the DEALER per the FACTORY SERVICE MANUAL and FACTORY INSTRUCTION SHEET ...

Well, the second one did not last very long so "i" did the THIRD one myself and it has lasted to 110,772.1 miles as of the last ride ...

What "i" am saying is that if installed correctly the OEM Front Motor Mounts will last a long time and that even applies to the AFTERMARKET "HEAVY DUTY ONE"S" ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Saturday, July 02, 2011 - 04:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ok just got my manual. It says "Tighten the two side isolator bolts(7) to 100-110 ft-lbs." No mention of any special torque procedure, or oiling the washers. Ironically in the related pic number 7 is a washer for the front iso bolt. WTF??


What is the torque of the rear iso bolts??

I really wanted to ride this weekend, I am getting closer & closer to making a chopper, seems hell of a lot safer!!

(Message edited by clyde the ape on July 02, 2011)
Top of pagePrevious messageNext messageBottom of page Link to this message

01x1buell
Posted on Saturday, July 02, 2011 - 04:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

hey do not waste a good buell on the bs please we need to keep the ones we have going ..
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Saturday, July 02, 2011 - 04:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I love the bike, I really don't want to kill it. But, I don't need the engine falling out. I wish someone made a new frame with better engine mounting system.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Saturday, July 02, 2011 - 05:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

A MECHANIC knows FACTORY SERVICE MANUALS are some times WRONG and miss leading !!!

There is lot of MECHANIC INFORMATION you have to be taught by a MECHANIC ...

The 2000 Factory Service Manual for the BLAST(P3) motor mount to head is 63 to 70 ft.lbs. ...

1997/1998 S3/S3T Factory Service Manual is 100 t0 110 ft.lbs. ...

1999/2000 S3/S3T Factory Service Manual is 100 to 110 ft.lbs. ...

So, IMHO it is up to a MECHANIC's interpretation what is over tightening, just right, or under tightening if the SERVICE MANUAL "WRITERS" put different SPEC's. in different manuals ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Saturday, July 02, 2011 - 05:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

CLYDE:
I do not have my FSM here to be sure BUT
I am willing to bet that some one will chime in here, I am positive that the Torque on the "Front motor mounting bracket to head bolts is not and probably has never been 110Ftlbs" its an aluminum part...

I believe that it WAS 75 ftlbs at one time, and that it was reduced and the procedure modified.

JRamsey if you have your FSM handy What is the correct spec for the X1 or S3


Clyde:
The bolts I am referring to face forward as viewed from either side of the bike, and attach the aluminum front bracket to the head, then a single bolt hangs that mount thru the front isolator, BTW if you are worried about the motor falling out dont
there are also several tie rods that secure it to the frame

I wheelie my X1 on occasion and have landed it hard more than once, motor never left the frame.

Buy the bolts from American Sport Bike when you call ask AL how to do it and how tite to secure them
he will set you straight ....

(Message edited by oldog on July 02, 2011)
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Saturday, July 02, 2011 - 06:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

100 to 110 ft.lbs. is TOO MUCH, "BUT" those that BELIEVE what ever is put in the FACTORY SERVICE MANUAL will "DO IT" !!!

This TORQUE SPEC. will be the same for S1, S2, X1, S3, and M2 models ...

Another way to look at TORQUE'ing is if the component will stay tight at a lower minimum torque amount, WHY TIGHTEN the component more !!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Saturday, July 02, 2011 - 06:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Straight from '99-'02 FSM

7/16" bolts for Iso mount to head 60ft.lbs.

1/2" main Iso bolt 100-110ft.lbs.

(Message edited by Jramsey on July 03, 2011)
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Saturday, July 02, 2011 - 10:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

OK I know some people take the service manual as the bible. I also know these books are NEVER 100% correct. I agree 100-110 ft-lb seems way too high, that is why I started this post. The manual says the same for the front iso bolt. I will try to scan the page & see if I can upload it. I went to HD dealer, they were about as helpful as an ejector seat on a helicopter.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Sunday, July 03, 2011 - 02:25 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)



Top of pagePrevious messageNext messageBottom of page Link to this message

Jramsey
Posted on Sunday, July 03, 2011 - 02:46 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)



Top of pagePrevious messageNext messageBottom of page Link to this message

13was13
Posted on Sunday, July 03, 2011 - 06:53 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The tightening-loosing-tightening procedure as well as torque, oiling etc. is described in the B-018 Safety Recall. http://www.badweatherbikers.com/buell/messages/384 2/263547.html?1277411168
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Sunday, July 03, 2011 - 07:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I saw the recall, but that means I need a new front mount.


Jramsey - My manual looks nothing like that.
Top of pagePrevious messageNext messageBottom of page Link to this message

Clyde_the_ape
Posted on Sunday, July 03, 2011 - 09:09 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)



« Previous Next »

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration