G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through October 02, 2010 » Thunderstorm Piston Squish Clearence « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Gympie
Posted on Monday, September 27, 2010 - 11:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just did a squish check on my new build using a Cometic .030 set with head and base gasket. Using .063 solder on the shelf, I get no compression on any of the solder. What is the stock squish clearence on T-Storm/Piston set up? Over .063?
Thanks,
Gympie
Top of pagePrevious messageNext messageBottom of page Link to this message

Sportyeric
Posted on Tuesday, September 28, 2010 - 04:11 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Oh my sorry tale can be read here:
http://www.badweatherbikers.com/buell/messages/384 2/451316.html?1272116118
The relevant info is Pammy's at the bottom.
Others with more knowledge than I will weigh in, but if I could do mine again, I would measure, as you have done, deck 35 thou if you are confident of your measuring, check again, then cc the chamber volume and enlarge if necessary to keep to 65cc (?) or more. (Which should give 10.7:1, if I remember correctly.)
I have built my Sportster engine in this fashion and am extraordinariy proud of its performance.
Top of pagePrevious messageNext messageBottom of page Link to this message

Gympie
Posted on Tuesday, September 28, 2010 - 12:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Going to do a squish check again using a larger dia. solder, say a 0.090 to see how far I am off. Not willing, as the post above, to mill the heads as the added expense of getting adj. pushrods and new covers. Have been told that a .025-.030 is optimum but even up to .090 it will only give up 3 bhp which I can live with.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sportyeric
Posted on Wednesday, September 29, 2010 - 01:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Harley sells pushrods that are 50 thou shorter than stock, so you wouldn't need new pushrod covers.
Stock lifters have a fair bit of leeway in them and if you haven't changed the valve seats, you can deck the heads quite a bit and simply let the lifters be compressed close to their bottoms when cold. As the engine heats and expands, the lifter will operate as it should. The play at the other end of the range, shortened by decking the heads, would only be used up by recession of the valve seat into the head as its pounded in over time. On used heads, I don' think that there would be much effect in that area.
If you are checking squish again, you could also reinstall the rockers and check how much play you have at the rocker-to-valvestem, do the math and figure how much more room there is to compress the lifter without ill effect. I decked my Sportster's S1 Lighting heads 33 thou and run stock pushrods. So far so good.
Top of pagePrevious messageNext messageBottom of page Link to this message

Scott_in_nh
Posted on Wednesday, September 29, 2010 - 02:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Not willing, as the post above, to mill the heads

According to NRHS, you adjust squish with head and base gasket thickness, other modifications should not be needed.

setting your squish clearance
Top of pagePrevious messageNext messageBottom of page Link to this message

Gympie
Posted on Wednesday, September 29, 2010 - 02:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Decided to have NRHS mill the head anyway, hoping Dan will know what he is doing. He states that .050-.060 may have to be taken off. Won't know until he does it. Just tick's me off that the Motor Company would sell T-Storm heads in the condition they are.
So ending up buying adj. pushrods and since I have not decided on a cam as yet the adj. pushrods will pan out. Oh BTW, Edelbrock has a great closeout price on the pushrods. Wish I could have gotten in on the price of their carbs, but sold out.
Now shopping for pushrod covers. Think I'll go with the Zippers setup. Too many people are having problems with the NRHS Hurricane covers with leaking at the base. He suggests using super glue to seal them. :-)
Had a conversation with Ken Weber of 10Litre Performance yesterday about squish. His opinion on squish is not to go below .040 on a street bike. This would allow for piston wobble, expansion of the rod and carbon build-up. Thanks for the suggestion on doing the rocker to valve measurement. Will do it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Gympie
Posted on Wednesday, September 29, 2010 - 02:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Yo, Scott.
Talking about T-Storm heads here which have a nasty deck casting on them. Take a look on NRHS's site for more information on them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Scott_in_nh
Posted on Wednesday, September 29, 2010 - 02:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

ok, sorry to post info that was useless to you - sounds like you have a plan in place.

good luck!
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluzm2
Posted on Wednesday, September 29, 2010 - 03:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Gympie,
You don't use the super glue to seal them, its used to hold the seal in place for installation.
Four small dots around the perimeter is all that's needed.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration