G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through April 12, 2008 » Stupid VDSTS Question??? H E L P!! « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Af226
Posted on Sunday, March 30, 2008 - 10:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

OK. Here it is. I got my used kit from a fellow BWB and loaded on the laptop. Plugged in the usb to the back of computer and here's the funny bit, where the hell do u plug into the bike. I assumed there would be a separate jack on the bikes computer...my bike has a grey connector on the throttle side and a black on the brake side, do I disconnect one of them and plug in, those plugs are a lot larger than the scan tool plug? Pictures are appreciated. Hopefully I don't sound to dumb seeing as I work in telecommunications for a living.

Thanks af226
Top of pagePrevious messageNext messageBottom of page Link to this message

Jos51700
Posted on Sunday, March 30, 2008 - 11:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Look at the front RH (as you sit on it) of the fueltank cover. There will be a small area behind the steering head, below the fuel tank cover, and the connector will be a small grey 4-pin connector living there. Originally, it had a rubber plug but that may be gone now. This plug is deadheaded, it hooks to nothing else but external computers.

The location is hard to describe, but it would be behind the front RH turnsignal in your profile picture of your bike. (under the fuel tank).

Confused yet?
Top of pagePrevious messageNext messageBottom of page Link to this message

Jos51700
Posted on Sunday, March 30, 2008 - 11:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Here.

Top of pagePrevious messageNext messageBottom of page Link to this message

Af226
Posted on Sunday, March 30, 2008 - 11:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Perfect, thanks man....needed that.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bluzm2
Posted on Monday, March 31, 2008 - 03:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Make sure you have the kill switch in the run position.
Things don't work do well with it in the kill position. Don't ask how I know that one for sure...
Top of pagePrevious messageNext messageBottom of page Link to this message

Af226
Posted on Monday, March 31, 2008 - 07:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

OK now I'm connected but having trouble getting any info from the ECM....does the bike need to be running?? It's connected through com port 1 without the keyspan.....my old P3 laptop wouldn't read the usb so it couldn't connect?? Is their supposed to be a book??

Again any help is appreciated
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Tuesday, April 01, 2008 - 10:09 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ok:

the short version,
all port settings must match the hardware

a. open the program off line and check the port settings ie program is set to com 1 and the port is actualy com 1,
[device manager]
b. make sure that no other soft ware is looking for it. (blocking use)

c. connect the cable to the bike, with the program running, then key on, kill switch on, Then on your keyboard press Ctrl + C, [ connect ] in a few seconds it should connect.

If you get an error post it here We will try to help.

the software communicates weather running or not.

HOWEVER

there is a time out that can kick in that will shut down the com port on the bike after 15 seconds on the first attempt
if you dont have "traffic" as I recall.

IF the settings are right and the cable is ok it works with the onboard com port.

caveot If the machine is running W98 you may have problems W98 serial comms could be "wonky" depending on the hardware check for version compatibility in the software help.
the tool is bloody simple other wise

(Message edited by oldog on April 01, 2008)
Top of pagePrevious messageNext messageBottom of page Link to this message

5liter
Posted on Tuesday, April 01, 2008 - 01:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I would get the "Keyspan" adapter. It solved my problem a couple of years ago.
Top of pagePrevious messageNext messageBottom of page Link to this message

Af226
Posted on Tuesday, April 01, 2008 - 10:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks for the help. Gonna play with it more on the weekend. I found the manual on the manufacture website.

Tx af226
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration