G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through February 25, 2007 » I rubbed it for hours today, but now my hand is sore! « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through February 21, 2007Mikexlr65030 02-21-07  08:02 am
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Hammer71
Posted on Wednesday, February 21, 2007 - 10:04 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I know but aint tellin. Also dropped off some of my mixture for the black areas. Will look so nice he wont want to part with it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Chasespeed
Posted on Wednesday, February 21, 2007 - 10:45 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Man, ya'll do things the hard way... doing this by hand???

Tx, if wanna polish, or learn, when you come back to TX, swing down, I have everythign you need... and will let you use the space... no worries...

Chase
Top of pagePrevious messageNext messageBottom of page Link to this message

Cmm213
Posted on Wednesday, February 21, 2007 - 06:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I cleaned my header like that once and then went out and rode very hard .They were gold in 2 hours, so I,m going to get them coated one of these days.
Top of pagePrevious messageNext messageBottom of page Link to this message

Captnemo
Posted on Wednesday, February 21, 2007 - 06:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

A dremel tool is a a polish nut's best friend. Then you step up in to dedicated polishing equipment.

My fav is a buffer with a scotchbrite wheel. Cleans, deburs and leaves a nice finish for the sisal wheel & black compound to start a real polish job. Find some knifemaker's green compound to end on a cotton or muslin buff and you'll never hand polish again...

.
Top of pagePrevious messageNext messageBottom of page Link to this message

Saintly
Posted on Wednesday, February 21, 2007 - 09:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

did you do the whole job with the compound or start out with sandpaper?

All I'm saying is: 80-220-600-1000........ w/H2O
Top of pagePrevious messageNext messageBottom of page Link to this message

Dmextreme
Posted on Thursday, February 22, 2007 - 12:12 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

i like the rye bread. good stuff.

btw nice job!
Top of pagePrevious messageNext messageBottom of page Link to this message

Xring60
Posted on Thursday, February 22, 2007 - 06:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

For protection/luster/all around good coating go with clear powder coat! Just make sure the powder coater masks off the critical areas! ie. where the fork tubes slide through the tree!
Top of pagePrevious messageNext messageBottom of page Link to this message

Xring60
Posted on Thursday, February 22, 2007 - 07:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Here is a picture of a clear powder coated surface. If you inspect it closely you can see orange peel but it also retains the original appearance.

Top of pagePrevious messageNext messageBottom of page Link to this message

Bake
Posted on Thursday, February 22, 2007 - 08:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Your telling me that you can clear coat with powder paint? Any idea how it holds up?
Top of pagePrevious messageNext messageBottom of page Link to this message

Xring60
Posted on Thursday, February 22, 2007 - 10:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Excellent! Adds about .005" total, I believe it is just as durable as a traditional powder coated surface.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration