G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through November 29, 2006 » Toe shift adjustment.... How to? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Beachbuell
Posted on Sunday, November 19, 2006 - 02:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

OK, I just got a new pair of riding boots today and I need to lower my shifter toe peg because my boots are a little thicker than the last. My question is, is there a adjustment for this? I have already adjusted the rear brake pedal, no prob there. I'm looking at the toe shifter and I see the two lock nuts (above and below a cylinder), the pivot point eye loops are threaded as if they can be adjusted up or down inside the cylinder. I've tried that, but it does not feel right and will not move. Am I missing something, or?
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Sunday, November 19, 2006 - 03:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You may need to adjust the transmission arm. It slides on to a splined shaft and has a pinch bolt that also engages a detent in the shaft. Remove the pinch bolt and slide off the transmission arm. Rotate it maybe one notch then reinstall. Do your fine adjustments with the threaded adjuster.
Top of pagePrevious messageNext messageBottom of page Link to this message

Samiam
Posted on Sunday, November 19, 2006 - 03:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

loosen both those nuts (one is reverse threaded) then turn the cylinder one way or the other to make the shift lever go up or down. Should be fairly easy to adjust. Then just tighten up the nuts and remember to test out the new position to make sure you can still ride.

Sam
Top of pagePrevious messageNext messageBottom of page Link to this message

Beachbuell
Posted on Sunday, November 19, 2006 - 04:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I figured out what the problem was. Both of the locknuts were seized onto their threads. They would spin, but not move up or down for adjustment. Anyhow, ended up with stripped threads on one. Will need to order a new part tomorrow. No biggie, at least now I know. Thanks guys.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hdbobwithabuell
Posted on Monday, November 20, 2006 - 10:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Beachbuell

I had the same problem with the threads. When you get the new parts, put a bit of anti-sieze on the threads.
Top of pagePrevious messageNext messageBottom of page Link to this message

Dcmortalcoil
Posted on Monday, November 20, 2006 - 11:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You really need to loctite the nuts and the bolts to the hollow tube. Otherwise, they'll come loose and completely come off.
Top of pagePrevious messageNext messageBottom of page Link to this message

Diablobrian
Posted on Monday, November 20, 2006 - 11:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just a drop of blue locktite, be sparing with it, or it will vibrate apart at the WORST possible time.
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Monday, November 20, 2006 - 11:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I safety wired mine. Works great.
Top of pagePrevious messageNext messageBottom of page Link to this message

Diablobrian
Posted on Tuesday, November 21, 2006 - 12:30 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Of course that's even better, but takes a little more work to do it the first time : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Mesafirebolt
Posted on Monday, November 27, 2006 - 02:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

The same day I adjusted mine and didn't locktight them because I wanted to make sure I was happy with the adjustment, IT happened!!! They had vibrated off and the adjusting sleeve went its own merry way. I limped home in 5th gear and had to make a new sleeve. USE THE LOCKTIGHT!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration