G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through August 21, 2006 » Lets see if this has ever happened to anyone else b4 « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Friday, August 11, 2006 - 06:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Okay heres what happened. just washed the bike. started it to let it warm up then took it around the block real quick to air dry the bike. get back, shut it off and proceed to dry off any remaining water drops. to find an oil leak by the swing arm. checked all the lines, nothing, fill/dipstick. nothing. after further inspection the swing arm cracked on the weld infront of the tire half way up the weld. and it leaks like 1 quart every 30 min. so i topped it off and took it to harley. 2 blocks from my casa. they were astonished to hear and see what happened. new swingarm being order monday. wtf could have caused it? i dont think debre. not much clearance between the tire and swingarm. and i was only goign 20mph threw the block. all input welcome
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Friday, August 11, 2006 - 06:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Are you sure it didn't get run over by a dump truck while you weren't paying attention?
Top of pagePrevious messageNext messageBottom of page Link to this message

Freyke
Posted on Friday, August 11, 2006 - 06:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

check for bullet holes...
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Friday, August 11, 2006 - 06:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

haha funny guys. but seriously.... i have a race kit witch has only been installed for a week exactly tomorrow. i dont think the added hp/touque could have caused this. seems like a faulty part from the factory? im lucky i didnt go on a ride right after washing the bike.
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Friday, August 11, 2006 - 07:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Agreed... sounds like a bad weld. Get a new one.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skyguy
Posted on Friday, August 11, 2006 - 07:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Good job spotting the problem. Nice to hear it is getting fixed quickly.

A bad weld can happen. It can also be hard to spot. Congrats on a unique issue! I am tired of hearing about the same old stuff. (:
Top of pagePrevious messageNext messageBottom of page Link to this message

Blake
Posted on Friday, August 11, 2006 - 07:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Ryan,

Any chance you can post up a photo of that cracked swingarm?

Please also email your VIN to me if you would, or just fill it in on your profile.

We definitely need to follow up on this very serious issue.

Thank you,

Blake
Top of pagePrevious messageNext messageBottom of page Link to this message

Whodom
Posted on Friday, August 11, 2006 - 08:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Remember that Buell changed the design (from one-piece to two-piece welded) and changed suppliers for the swingarm in 2006.
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Friday, August 11, 2006 - 08:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

"Blake"
ill try to get one when they have it appart either monday if they get to it or when they are installing the new one. its to tight of a spot to get a pic with the bike together. but ill be sure to keep updated on my situation.
Top of pagePrevious messageNext messageBottom of page Link to this message

Blake
Posted on Friday, August 11, 2006 - 09:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Excellent, thanks Ryan.

My first name is really Blake, really. : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Diablobrian
Posted on Saturday, August 12, 2006 - 12:13 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Good eye catching this. This is the first problem I've heard of with the new design swing arm.
Top of pagePrevious messageNext messageBottom of page Link to this message

Xb12rdude
Posted on Saturday, August 12, 2006 - 01:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

When you washed it was it hot from riding?????
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Saturday, August 12, 2006 - 03:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

When you washed it was it hot from riding?????

it was sitting in the garage for about 2 hrs. after rideing it. i felt the cases and swing arm b4 i even started. it was warm but not hot. i didnt even use water for about another hour. i first sprayed the bike with grease lightning, to disolve the brake dust. then used a wash mit with soapy water on it to rinse it off. but the water in the bucket was car wash water. so after the soapy rinse down i sprayed the bike off. the whole time the bike was not hot. no steam, no fast evaporation of water. just warm to the touch as if it were to be sitting in the sun all day.
then i started the bike and it ran in the drive way for a little while it warmed up and started to dry its self off. when that started i took it around the block once. but before i left there was no oil on the ground. after coming back parking it and shutting it off. there was an oil puddle by the time i walked to get a microfiber towle to finish drying it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Altima02
Posted on Saturday, August 12, 2006 - 10:03 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

was the rear axle ever torqued down without the swingarm brace installed? That would be my only guess as to what could have caused it, beside just "one of those things"
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Saturday, August 12, 2006 - 12:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

was the rear axle ever torqued down without the swingarm brace installed? That would be my only guess as to what could have caused it, beside just "one of those things"

good question. that could be something to look into. but ive never had the rear apart yet. only 2700 mi on the bike. so it could have happened at the factory. ill bring up that issue with the dealer. it sounds plausable
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Wednesday, August 16, 2006 - 08:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

a little update on my bike. they havent taken it appart yet. but swing arm is 2 weeks out. and the service writer says everyone in the shop thinks ive been doing stoppies. but thats wrong. im not that insane. ill post pics of the swing arm when i get the bike back
Top of pagePrevious messageNext messageBottom of page Link to this message

Tiburondriver47
Posted on Wednesday, August 16, 2006 - 09:24 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I had the same problem back in June. The leak was about 6" up on the wield. It was replaced under warrenty.I wasn't doing stoppies either. Even if you were that wield should hold.
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Thursday, August 17, 2006 - 03:05 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

you had the same problem too?! im glad im not the only one. did they give any reason for it happening?
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Wednesday, August 23, 2006 - 08:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

update!! got the bike back today. checked out the old swing arm adn there was a 6 inch crack straight up the weld in the exact center. i have pics and will post them after i get out of the shower.
Top of pagePrevious messageNext messageBottom of page Link to this message

Deflaytedwayz2
Posted on Wednesday, August 23, 2006 - 09:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)



here are the pics of teh crack. the best pics i could get
Top of pagePrevious messageNext messageBottom of page Link to this message

Blake
Posted on Thursday, August 24, 2006 - 01:52 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Excellent! Thanks for the follow-up!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration