G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through May 19, 2011 » Exhaust emulator questions (electronics gurus)...... « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Gunut75
Posted on Monday, May 16, 2011 - 11:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm planning on making an emulator. I dug up this old thread.
http://www.badweatherbikers.com/cgibin/discus/show .cgi?tpc=32777&post=332834#POST332834
10K resistor, no problem. What does the 1K2 notation for the other resistor mean? 1.2K Ohms? 1K, 2w (huge)?
Also, the BC337 transistor supposedly can be substituted with a 2N4401: Is this true?
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Monday, May 16, 2011 - 11:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

1.2k ohm
Top of pagePrevious messageNext messageBottom of page Link to this message

Gunut75
Posted on Tuesday, May 17, 2011 - 07:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

OK. So, they didn't have a 1.2K ohm resistor, so I picked up a 1K ohm, and a 220 ohm. Will the extra 20 ohms make a difference?
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Tuesday, May 17, 2011 - 08:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

You can probably get away with the 1K. I'm having a hard time figuring out what is happening with the control and device. Is the motor really a 12 volt device or is it 5 volts regulated? If twelve then I can understand it, but if 5 then I don't know why that resistor is in there.

I have a 9R so I can't look in the book to help. So I would suggest measuring the voltage on a working system between ground and the white wire.

I would guess the tolerance on that bias resistor is probably 2K to 1K, but again just a guess. So in short I don't think the extra 20 ohms will be an issue. And the more I think about this, it is probably better to use a 10K between power and the white wire (pull up resistor). So let me go through what I think is happening:

--------------------------------------------
During the closed low RPM that white wire remains high (+v)

When the valve is supposed to do whatever it does, the white wire is pulled low. This cause the transistor to conduct and pull the tan wire low.
--------------------------------------------

That is unless it is the opposite, I didn't look to see if the transistor was an NPN or a PNP so my description could be backwards.
The resistor for power (1.2K) is used to make sure that the pull up does not draw too much current, which is why I say a second 10K might do the job.
Top of pagePrevious messageNext messageBottom of page Link to this message

Gunut75
Posted on Tuesday, May 17, 2011 - 10:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That sounds logical to me. I did get a package of 10K resistors. I will see if my multimeter at work actually still works. If not, it's time to get a new one (been 10 years). Anyone out there have a multimeter and a 12? It will take me a couple days to get this done. I have the cage tomorrow.
Ourdee's explanation in this one should help.
http://www.badweatherbikers.com/buell/messages/406 2/571774.html
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration