G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through December 02, 2010 » XB9 Ignition and Key Switch Relays getting hot? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Mk2mike
Posted on Monday, November 08, 2010 - 05:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Hello there, sucks to have my first post be about an issue with my bike.

I was riding around town the other day and my bike just quit on me. No power, so I figured a fuse popped or what not. Popped my seat to find smoke coming from my relays.

My key switch relay had MELTED!!! and my ignition one was to that point.

What would cause this? I checks all over for a short and didn't find anything!! No codes, etc.

Is it normal for them to be warm?


Here is a picture of the relay, don't mind the bent prongs. Burt the crap out of me when I pulled it out so I threw it on the ground haha

Top of pagePrevious messageNext messageBottom of page Link to this message

Glitch
Posted on Monday, November 08, 2010 - 05:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Could it just be a bad relay?
Maybe it got stuck in the energized position?
I'm just guessing here since you already checked for shorts.
Top of pagePrevious messageNext messageBottom of page Link to this message

Luv2spd
Posted on Monday, November 08, 2010 - 08:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Relays are installed in your bike to save the electrical components of your bike. They burn out either if there is a lot of vibration or if there is high voltage coming from the alternator. I'm not sure why yours melted, but when one of my spark plugs didn't work and I tried to start the bike because I didn't know what the problem was, the relays were clicking on start up and were very hot. I bought a few relays since I have my bike, but the relays that I bought do not look like yours, they are light gray. Maybe you had the wrong relay in, that could cause it to melt too.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mk2mike
Posted on Monday, November 08, 2010 - 08:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Very possible. Yeah I replaced my relays with OEM ones from the Dealer. But they still get quite hot.

When that relay took a dump, it melted a portion of the fuse panel as well
Top of pagePrevious messageNext messageBottom of page Link to this message

Luv2spd
Posted on Monday, November 08, 2010 - 08:48 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

http://www.badweatherbikers.com/buell/messages/327 77/583876.html?1281491085

If you search the site long enough I think there was a thread here that had a website where you can buy a new fuse box in case you want to change yours to a new one.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mk2mike
Posted on Monday, November 08, 2010 - 09:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

The fuse block doesn't really bother me too much. Getting some new female spade connectors specific for the box though. I would love.

Thank you for the link to that thread though. I did pull my box apart, and realized, "how am i going to clean this little thing!"

The bike runs again, but I just don't ride it far, as Im worried it will build up heat again.


I'm really surprised the oem relays were only $5.00 each at the harley dealership.

Was expecting a much bigger hit.
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Monday, November 08, 2010 - 09:56 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

http://www.badweatherbikers.com/buell/messages/327 77/597629.html?1287657950
Top of pagePrevious messageNext messageBottom of page Link to this message

Mk2mike
Posted on Monday, November 08, 2010 - 10:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

THANK YOU!

I will contact my dealer tomorrow about ordering some new terminals. Bike just recently has been giving me tons of electrical issues. But considering it's 7 years old... it's bound to happen.

I think I like this forum far more then Buellxb.com :P
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Monday, November 08, 2010 - 10:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I'll be at 4 weeks waiting on Thursday.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mk2mike
Posted on Monday, November 08, 2010 - 11:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Really? From the dealer?
I found a site that carries them at 1.25/each but the shipping was 10 dollars! for something you can put in an envelope!
Top of pagePrevious messageNext messageBottom of page Link to this message

Glitch
Posted on Tuesday, November 09, 2010 - 06:49 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

But considering it's 7 years old... it's bound to happen.
Bite your tongue man!
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Tuesday, November 09, 2010 - 09:48 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Which site, I may look into canceling my order, it was from Chicago Harley because you can order anything online and google indexed the part numbers. They were less than $1 each and I ordered 10 of each for a grand total of about $27 with shipping. If I had known it would take this long I would have stopped at my local dealer and ordered them.

I think the problem is that Harley has to two step these parts from Ford, they should have gotten OEM status so they could order directly from Molex. You might be better off using the Ford part and going to any auto store, my AutoZone has the fuse block terminals hanging in blister packs on the shelves, of course I found that after I ordered them on the web, but the fuse terminals have been in for weeks now waiting on the relay terminals.

The use of Ford parts was great for availability, I just wish they had used Ford part numbers so we could easily cross reference and obtain everything.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mk2mike
Posted on Tuesday, November 09, 2010 - 11:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Yeah, I know I googled the HD pn, and not much came up. I have a few buddies that work at a Ford dealer, maybe possible to get them to check out the connector and maybe something will come to mind.

Oh well, figure i'll just stare at the bike until I figure it out. Don't want to risk burning the whole mofo'er down.

Really scared the heck out of me when I saw tons of smoke coming from her...
Top of pagePrevious messageNext messageBottom of page Link to this message

Glitch
Posted on Tuesday, November 09, 2010 - 11:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Really scared the heck out of me when I saw tons of smoke coming from her...
I'll bet that was one of those heart skip moments for sure.
Don't know whether to run or find the source.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mk2mike
Posted on Wednesday, November 10, 2010 - 01:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Yeah it was pretty scary. But Oh well! Time to fix it! : )
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration