G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Ecmspy questions « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through April 08, 2010Gunut7530 04-08-10  09:05 am
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Jaylightnn08
Posted on Thursday, April 08, 2010 - 12:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

well looks like i spoke too soon. It was running good yesterday so I took it out again this morning. It started up ok, when its idleing it will idle smooth, then through a little pop in every couple of seconds. I wish i could figure out how to post my timing charts on here. I think the timing might be the issue now, or a partially clogged injector, something. I dont know I am just grabbing at straws now. I wish i could get ecmread to work. When i try to start ecmread " the program cant start because mono.dll is missing from your computer" Ive tried reinstalling, to no avail. I cant get mono to download the right way i guess, i dont know, the place where you download mono from has like fifty different versions of it and its not clear what version you should be using for ecmread. Ive been downloading the one " mono 2.6.3" or something like that. Dont know, Im over getting mad and frustrated. I love my bike, when it runs, Its not the bikes fault. ITS OBAMAS FAULT, HHAHA JUST KIDDING I ALWAYS WANTED TO BLAME HIM FOR SOMETHING PUBLICALY
Top of pagePrevious messageNext messageBottom of page Link to this message

Xoptimizedrsx
Posted on Thursday, April 08, 2010 - 09:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

download mono and Install it.
download ecmread Install it.
place read and mono in same location same folder. restart the computer.

It will work now.

mike
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Thursday, April 08, 2010 - 10:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Click this link to download Mono.

http://ftp.novell.com/pub/mono/archive/2.6.3/windo ws-installer/4/mono-2.6.3-gtksharp-2.12.10-win32-4 .exe

If that doesn't work, go here:
http://www.go-mono.com/mono-downloads/download.htm l

Assuming you are using Windows, pick Windows, then click "Mono for Windows, Gtk#, and XSP"
Top of pagePrevious messageNext messageBottom of page Link to this message

Jaylightnn08
Posted on Friday, April 09, 2010 - 04:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

yea, thanks froggy, i tried but my computer says that mono is already installed so i tried to delete EVERYTHING on my comp that says mono and it says its still there. At this point, im done with it. There are other programs that are MUCH MUCH easier to use. One thing ive noticed that has always been true in MY life is, you get what you pay for. The program is free, enough said. Thanks anyways, if it ever gets easier to accquire i will try again.
Justun
Top of pagePrevious messageNext messageBottom of page Link to this message

Id073897
Posted on Friday, April 09, 2010 - 06:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Better for your bike that you don't get it running.
Top of pagePrevious messageNext messageBottom of page Link to this message

Xoptimizedrsx
Posted on Friday, April 09, 2010 - 08:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I can guarantee you will not get any program as complete as the ecmread and tunerpro combo.

I'm with Id07 at this point. It may not be working for you as a safety to keep the bike from blowing to pieces.
Top of pagePrevious messageNext messageBottom of page Link to this message

Dallasb
Posted on Friday, April 09, 2010 - 08:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I have an '06 xb...is there any advantage to using the ecmread/TP combination as opposed to my current ecmspy/MLV combination?
Top of pagePrevious messageNext messageBottom of page Link to this message

Xoptimizedrsx
Posted on Friday, April 09, 2010 - 10:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

much more detail in the complete ecm.
Top of pagePrevious messageNext messageBottom of page Link to this message

Id073897
Posted on Saturday, April 10, 2010 - 04:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I have an '06 xb...is there any advantage to using the ecmread/TP combination as opposed to my current ecmspy/MLV combination?

These two combos aim at different targets. tunerpro is an eeprom editor and ecmread is just a little helper for fetching and burning data. MLV is log file analysis and logging requires ecmspy, as ecmread is not capable to do so.
Top of pagePrevious messageNext messageBottom of page Link to this message

Krueger08xb12s
Posted on Saturday, April 10, 2010 - 10:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

So for an 08+ xb it's best to use ecmspy for datalogging and getting real-time data then use ecmread to read/write new a/f and timing values?? Gunter, xopti, thanks for all the time & effort you both put into this program. I have a small dip in power @ about 50%-75% open throttle from 4-5kRPM. I just got the cable in the mail yesterday and I'm ready to fetch data from the EBR Race ecm. Am I in left field by thinking I should add a little more fuel to the affected cells (possibly drop the value by 0.5) and lightly adjust from there to level out the dip?
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Saturday, April 10, 2010 - 10:29 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Do these work on the EBR race ECM?
Top of pagePrevious messageNext messageBottom of page Link to this message

Id073897
Posted on Saturday, April 10, 2010 - 11:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

No idea. Don't have an EBR ECM for testing, just an older DDFI-2 factory race, and it's working with that one.
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Saturday, April 10, 2010 - 11:55 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I guess we'll find out when Krueger gives it a test.
Top of pagePrevious messageNext messageBottom of page Link to this message

Id073897
Posted on Saturday, April 10, 2010 - 03:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Great. Then, please, let me know.
Top of pagePrevious messageNext messageBottom of page Link to this message

Xoptimizedrsx
Posted on Sunday, April 11, 2010 - 02:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I'm just a middle man, I only did test on how to use it and posted that data. I did ask Gunter for tips on how to move files around better.

Gunter and his direct crew or Just himself did all the real work.

give credit to Gunter.

Mike
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration