G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through February 23, 2010 » Swingarm pivot shaft « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ta_borom
Posted on Thursday, February 11, 2010 - 09:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Can anynody tell me if the swingarm pivot shaft that attaches into the engine case on a 1125R matches the one on an xb9???
Top of pagePrevious messageNext messageBottom of page Link to this message

Aj2010
Posted on Thursday, February 11, 2010 - 07:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I am trying to find out that very same thing. The 1125 part certainly seems to be a beefier piece though
XB pivot shaft

XB pivot shaft
,
1125 pivot shaft

1125 pivot shaft
Top of pagePrevious messageNext messageBottom of page Link to this message

Sharkytattoo
Posted on Thursday, February 11, 2010 - 10:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Why do you need to know this? Are you thinking of swapping them? And again, why? Only time these EVER get bent or damaged, are when bike is crashed. Oh, or installed incorrectly by someone without a service manual.
Top of pagePrevious messageNext messageBottom of page Link to this message

Aj2010
Posted on Saturday, February 13, 2010 - 11:34 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Shark, the why for me is that my project bike (well one of them) requires a pivot bolt and I would rather go with the stronger part (the 1125 pivot bolt is also cheaper) Bearing for the xb are
#6204 so xb pivot shaft has a diameter of 20mm, width of swingarm at pivot measured from outside to outside is 135mm. Any one know the dimensions of the 1125 pivot bolt or swingarm?

(Message edited by aj2010 on February 13, 2010)
Top of pagePrevious messageNext messageBottom of page Link to this message

Aj2010
Posted on Sunday, February 14, 2010 - 10:49 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Ta, I received some info on the 1125 board (thanks Froggy). Bearings on both XB and 1125 are the same, the 1125 uses the Uly spacer tube so both width and diameter must be the same. Based on this info I purchased one on E-Bay. I will be able to give you measurements or other info once it arrives.
Top of pagePrevious messageNext messageBottom of page Link to this message

Aj2010
Posted on Wednesday, March 10, 2010 - 09:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

OK Ta, I have the 1125 bolt. It does fit the XB swing arm. I can give you dimensions of the head but not thread pitch as neither of my thread gauges has coarse enough pitch.
The diameter of the head is 32mm / 1.25"
The width or thickness of the head is 23mm / 0.9"
Hope this helps and sorry for the big delay
Top of pagePrevious messageNext messageBottom of page Link to this message

Aj2010
Posted on Wednesday, March 10, 2010 - 09:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

OK Ta, I have the 1125 bolt. It does fit the XB swing arm. I can give you dimensions of the head but not thread pitch as neither of my thread gauges has coarse enough pitch.
The diameter of the head is 32mm / 1.25"
The width or thickness of the head is 23mm / 0.9"
Hope this helps and sorry for the big delay
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration