G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through July 12, 2009 » Tranny shifts great when cold, grind'em till you find 'em when hot « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Spacecapsule1
Posted on Friday, July 03, 2009 - 08:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

....fluid level too high? I thought i read that somewhere.... any ideas? Last time i checked, the dealer had the fluid level to where it poured out of the clutch inspection cover. I removed a lot and brought the level down to just touching the gear teeth....
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Friday, July 03, 2009 - 09:05 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Check your primary chain tension. Sounds like it is set too loose/tight, and once it warms up it is way out of spec.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sifo
Posted on Friday, July 03, 2009 - 09:22 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Fluid will come out of the cover if it's on the side stand. It should be checked with the bike up right. As Froggy suggested, check the primary chain tension.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fast1075
Posted on Friday, July 03, 2009 - 09:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

+1 on the primary adjustment..also double check the clutch adjustment..normally the clutch will engage at the end of lever travel...if it engages close to the grip, you have too much slack.

If the clutch does not release cleanly when you shift, it will cause the symptom. Buell clutches tend to drag some when hot..
and we have truck transmissions..there is a lot of rotating mass in there...be sure to shift with authority...
Top of pagePrevious messageNext messageBottom of page Link to this message

Gunut75
Posted on Friday, July 03, 2009 - 10:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Mine has the same thing going on, only not as rough as yours. My primary is to be checked soon.
Top of pagePrevious messageNext messageBottom of page Link to this message

Spacecapsule1
Posted on Friday, July 03, 2009 - 01:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

k thanks. fluid poured out wit the bike upright, not on sidestand. I corrected that. I thought I had my chain right, but who knows....

the clutch is adjusted right for sure. the chain is open to interpretation it seems.
I do shift with authority, thats the only way it will shift.

I need to re-check my fluid level i guess.
Top of pagePrevious messageNext messageBottom of page Link to this message

Prof_stack
Posted on Friday, July 03, 2009 - 10:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

My XB9S always had downshifting clunks when the tranny was hot, unless I downshifted firmly and before coming to a stop. There were some pretty loud CRUNCHES until I got tough with it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ochoa0042
Posted on Friday, July 03, 2009 - 11:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

what is it.. like .8 of a quart goes into the primary?
Top of pagePrevious messageNext messageBottom of page Link to this message

Cymro
Posted on Sunday, July 05, 2009 - 12:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Sounds like a dragging clutch to me.
Top of pagePrevious messageNext messageBottom of page Link to this message

Spacecapsule1
Posted on Sunday, July 05, 2009 - 02:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

its the famous 1st to 2nd gear change that's the most trouble.
Top of pagePrevious messageNext messageBottom of page Link to this message

Americanmadexb
Posted on Sunday, July 05, 2009 - 03:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

1st to 2nd has always been alittle clunky for me since day one. Mostly when shifting in higher RPM's. If i shift in the 2,500-3,000 RPM range its fine.
Top of pagePrevious messageNext messageBottom of page Link to this message

Brent_crossbronkos
Posted on Monday, July 06, 2009 - 07:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Both my 04 12s and 04 9s need to be short shifted into second when hot to avoid the "crunch". Have ridden others that are the same. A 2500 rpm shift seems to work best. When cold - shifts like butter! My 06 9s shifted great hot/cold into 2nd but always clunked into 3rd (helical cut gears in trans). Fluid levels, chain adj had no effect whatsoever on the 2nd gear hot crunch and both these bikes were near brand new when I bought them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Fast1075
Posted on Monday, July 06, 2009 - 08:58 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I had pretty bad problems with crunchy/missed shifts..on one ride I nearly crashed twice due to missed shifts coming out of corners...

The symptoms indicated a dragging clutch when hot...in tandem with a "clunky" gearbox design (or more correctly..executed).

I took the clutch apart, expecting to find obvious problems or damage...nope...no warped or overheated steels...no baked fibers...no damage or warping of the diaphragm spring, etc...

In anticipation of the clutch teardown, I had bought a new clutch kit from Energy One...so I installed it to see if it made any difference...I installed the kit and properly adjusted everything and installed new oil...used Mobil-1 v-twin oil...that made a huge difference in how it behaves...it did not magically make it shift like an import bike...but a lot better..but no more missed gears or grinding...
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration