G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through November 09, 2008 » NEED HELP!!! I think a sensor went bad, but dont know « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Juniorkirk
Posted on Wednesday, October 29, 2008 - 03:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I just got done washing her about 45 minutes ago and wiped her down good so no water spots would show up. Then I went for a little ride to get the rest of the water off her.

Now for the bad part....

I turned the key on, and both needles do their full range of motion thing. Started her up and the tach kicks up to just over 1k. So far so good. I start moving and I look down and i notice that my Speedometer needle is sitting at 0, and I'm going probably 30 or so. Went a little farther and noticed that my tripometer is doing the same thing, sitting at 42.9 miles. I thought it was just a little bug thing, so i switched her off and back on. Once again BOTH needles move, and when i started it the tach kicked right up. But when i start moving, the speedometer just sits there. I rode about 15 miles and not 1/10 of it was put on my tripometer.

I'm not sure what went out, but it was all started after i gave her a nice bath. Any help on this would be great, guess i'll have to use my GPS for my speed and how far I've gone so i don't get stranded on an empty tank.
Top of pagePrevious messageNext messageBottom of page Link to this message

Sub65chris
Posted on Wednesday, October 29, 2008 - 03:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

speed sensor. around 40 bucks and one alen screw to fix. simple and easy.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Wednesday, October 29, 2008 - 03:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Speed sensor : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Iamarchangel
Posted on Wednesday, October 29, 2008 - 03:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Faint hope clause going off the wash info: open up your sprocket cover, spray everything with WD40.

If you want to, open up the sensor connector and spray it directly.

First take a photo of how the wires are laid out. It's a challenge to get it back the way it was.

Probably won't do any good, but the sensor is about $80 so it's worth a shot.

Yes, it does a full sweep even though it's not working. The gauge is telling it would be working if it had any info to give you from that sensor.
Top of pagePrevious messageNext messageBottom of page Link to this message

Juniorkirk
Posted on Wednesday, October 29, 2008 - 04:07 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

thanks, i'll give that a try here in a bit. Hopefully just spraying it with WD40 will work, if not, i'll just grit down and guy buy a new one
Top of pagePrevious messageNext messageBottom of page Link to this message

Moosestang
Posted on Wednesday, October 29, 2008 - 05:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

My speedo doesn't sweep most of the time, but it still works.
Top of pagePrevious messageNext messageBottom of page Link to this message

Iamarchangel
Posted on Wednesday, October 29, 2008 - 09:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

My speedo doesn't sweep most of the time, but it still works.

I think you have to clean it and/or start looking for a new instrument panel soon?
Top of pagePrevious messageNext messageBottom of page Link to this message

Juniorkirk
Posted on Thursday, October 30, 2008 - 11:04 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

i didnt have any WD40 around me so i just hosed it down really good with water. Still didnt work, but as soon as i got into her it started bouncing around. Then it looked like it was working fine until i stomped on the throttle, and the speedo would drop until i leveled out on the throttle. It did that for about 45 minutes until i got to I-5 and got to get some speed going. At about 100 the speedo went from about 10mph to 100mph and it's been working ever since without a problem. Still probably gonna buy a new sensor and replace to be on the safe side.
Top of pagePrevious messageNext messageBottom of page Link to this message

Iamarchangel
Posted on Thursday, October 30, 2008 - 03:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I would say leave it, just be careful not to spray any water into that area any more. Unless you want to waterproof it but that can get involved.

You might want to take the sensor out from the case, leave the wiring intact, and check the bottom of it. There might be some filings there that would interfere. Best to leave it until you have to change it unless you want the practice.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bombardier
Posted on Friday, October 31, 2008 - 10:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Pull the plugs behind the drive sprocket plastic cover and spray with WD-40.

This will provide a bit of waterproofing for the next time you wash it and when you next ride in the rain.

(Message edited by Bombardier on October 31, 2008)
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration