G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Buell RACING & More » Racing - Circuit/Road Racing » Archive through April 07, 2010 » XB12R Front Sprocket « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Thursday, January 28, 2010 - 11:17 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Any suggestions where I might find a 23 tooth for Daytona? I'll settle for a 22 if that is all I can find. EBR does not have any XB sprockets and they suggested Street & Comp, who are currently out of stock.
Top of pagePrevious messageNext messageBottom of page Link to this message

Neb25
Posted on Thursday, January 28, 2010 - 05:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Most guys on a XB will use a 22 front and 42 rear at Daytona. 23 front would need a 44 rear. I have also run a 21 front and a 40 rear. two teeth on the front = one at the rear as far as changes go. 1 tooth at the rear equals about 300 rpm change in top gear.

Dennis Kirk sells them. They are made by PBI Sprockets.
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Thursday, January 28, 2010 - 09:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I'm using the stock swingarm so I wanted to run bigger sprockets to keep the chain away from it, similar in size to the belt pulleys. A 23 / 46 would be close to what your running, a 2.0 gear ratio, and keep the chain up and away from the stock swingarm. Your 22 / 42 comb is a 1.90 gear ratio so I would be right in the same ballpark.

I may be off base here, this is my first Buell, but looking at clearances around the swingarm, I just felt trying to stay close to stock pulley size's would give me the best clearance while still accomplishing the same gearing ratio's.

Thank's for your insight.
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Friday, January 29, 2010 - 10:32 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Anyone at least know what the off-set is?
Top of pagePrevious messageNext messageBottom of page Link to this message

Rhun
Posted on Tuesday, February 02, 2010 - 04:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I think most guys use the PRP sprockets for the front. Several places sell them.
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Friday, February 05, 2010 - 03:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Michael at EBR found a source for XB12R sprockets and they have plenty in stock, all sizes 17 – 27 tooth. They carry PBI sprockets that will work with EBR’s trans output shaft nut, part # CD0009.02AH. Order part number 277X then tell them the number of teeth you need. Just thought I’d pass the information along. Michael & EBR have been a big help to me with getting my bike ready in time for Daytona.

Chris Products
5605 NE Elam Young Parkway
Hillsboro, Oregon 97124
(503) 645-6500
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Friday, February 05, 2010 - 04:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Playhard, I think I have a 23 tooth for a 520 chain. I'll check when I get home. If I have it, it's your's if you cover the shipping.
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Friday, February 05, 2010 - 04:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just PM me your address, and if I have it I'll get it out to you right away. Just hook me up whenever.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skinstains
Posted on Saturday, February 06, 2010 - 01:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just wondering, what year swingarm are you using and do you have any protection on it at all as far as chain slap is concerned ?
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Saturday, February 06, 2010 - 04:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I'm using the stock (2009) swingarm with a FreeSpirits adjustable tensioner. Yes, I'm making a chain-guide for the top of the swingarm.
Top of pagePrevious messageNext messageBottom of page Link to this message

Alessio66xb12r
Posted on Saturday, February 06, 2010 - 06:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

to neb25 : "2 teeth front = 1 tooth rear"
WRONG !!!!
To playHard in Mugello (1,1 km straight) a good 88" xb uses a 21/47 with the stock 12 primary ratio a final ratio of 1.9 or 2.0 looks to me crazy "long" ...just a guess .
how long is that straight ?
bye Alessio
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Saturday, February 06, 2010 - 06:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I'm guessing since the entire Daytona tri-oval is 2.5 miles, the run from NASCAR turn 3 to the braking zone of turn one is right at one mile. Three different people, who all ran Daytona last October recommended about a 22 / 42 or 1.90 gear ratio.
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Saturday, February 06, 2010 - 06:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

That would be about 1.7km
Top of pagePrevious messageNext messageBottom of page Link to this message

Alessio66xb12r
Posted on Sunday, February 07, 2010 - 04:23 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

1,7 km is a loooong straight i did not suppose so long so maybe a ratio of 2 or a bit less will be ok but my point is : what kind of power ...better what kind of mods do you have to hit 7200/7300 in 5th with such a long ratio..
hope you understand what i mean.
good luck Alessio.

p.s.

i had the same chain conversion using a long ss swingarm on mine and a good way to change sprockets was to have 2 or more chains,keep the chain tensioner as low as possible so the the chain passes far from the swingarm (bottom) because you WANT to protect the swingarm (i did with teflon) on top and ,good but not really necessary with a proper chain longness, on the bottom side too.
good luck again
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Friday, February 12, 2010 - 12:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

The sprocket is on it's way. I sent it out yesterday.
Top of pagePrevious messageNext messageBottom of page Link to this message

Playhard
Posted on Friday, February 12, 2010 - 03:44 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Eboos, Thanks a million!!!
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Friday, February 12, 2010 - 03:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Sorry I didn't get it out earlier. Work schedule is pretty busy.
Top of pagePrevious messageNext messageBottom of page Link to this message

What_the
Posted on Saturday, February 13, 2010 - 09:44 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Al,

If your swingarm is the newer diecast version, the XBRR chain rub should snap right into place. You are using a PBI sprocket and EBR sprocket nut, so that leads me to believe the chain line would correct for the XBRR/XB chain rub.

Send me an email,
Michael
Top of pagePrevious messageNext messageBottom of page Link to this message

Eboos
Posted on Monday, March 01, 2010 - 09:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Congratulations on the 3rd place finish in Expert LW Supersport.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration