G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through June 22, 2010 » Did I do this? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Seanp
Posted on Sunday, June 13, 2010 - 01:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Ok, so I went to put on a new front muffler clamp, as mine has been broken for a few months now. I just haven't had a chance to get around to fixing it. As I was doing that, I found out that one of the rear clamps was broken as well. Well fondogiddyap, I guess I'll order one of those too. Then I decided to do a general exam of the exhaust, and found this:



I also found the exhaust stud was broken off (AGAIN - the third time this has happened.) Are these problems the result of not fixing the front exhaust strap quickly enough?

So . . . I guess I need a new header. Anyone know how much that will cost? I looked in the classifieds here and nobody has one, and I looked on ebay and didn't see one.

I did successfully fix one thing - the wire for the headlight ground broke on Friday, (for the second time - seems like a design flaw) and I patched that up easily.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hughlysses
Posted on Sunday, June 13, 2010 - 01:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I'd say odds are good that not fixing the strap immediately led to the other problems.

A good welder could repair that; you might check with some local shops and see what they say. Should be done using TIG for best results.
Top of pagePrevious messageNext messageBottom of page Link to this message

Xbeau12s
Posted on Sunday, June 13, 2010 - 07:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

+1 on the welder. Chances are if you find a good one the pipe will be stronger than when new. Shouldn't be hard to do for them either.
Top of pagePrevious messageNext messageBottom of page Link to this message

New12r
Posted on Sunday, June 13, 2010 - 07:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I have welded a crack like that with success.
Top of pagePrevious messageNext messageBottom of page Link to this message

Badbuell08
Posted on Sunday, June 13, 2010 - 09:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

http://cgi.ebay.com/ebaymotors/BUELL-XB9R-XB12R-FI REBOLT-03-EXHAUST-HEADERS-CANS-O2-_W0QQcmdZViewIte mQQhashZitem439f6232f6QQitemZ290436821750QQptZMoto rcyclesQ5fPartsQ5fAccessories
Buell header on flea bay if you want to go that way

hope it helps and you get it fixed
Jeff
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikef5000
Posted on Sunday, June 13, 2010 - 10:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Not fixing your front strap most definitely caused the header and stud breakage.

All of the weight and stresses that the front strap is meant to hold was put on the header and studs.
Top of pagePrevious messageNext messageBottom of page Link to this message

Seanp
Posted on Monday, June 14, 2010 - 06:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Ok, so will welding the header make it strong enough, or do I need to buy a new one? I'm not sure I want to spend a hundred bucks (or whatever welding would cost) on a bandaid when what I really need is a replacement...
Top of pagePrevious messageNext messageBottom of page Link to this message

Ratbuell
Posted on Monday, June 14, 2010 - 08:21 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Put it this way...if you get it welded properly, and it cracks again, I can practically guarantee the new crack will NOT be on the weld.

Not to say you don't possibly have additional weak spots on the header....
Top of pagePrevious messageNext messageBottom of page Link to this message

Yool
Posted on Monday, June 14, 2010 - 10:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I've got two cracks in my header, (possibly caused by no front exhaust clamp)

But the cracks run along the header, around the bend. One on each side.
I think they co-incide with the point between where the metal stretched on the outside of the bend, and compressed on the inside of the bend.
Maybe all headers were not created equal, and QA issues decree that some will crack,
(No doubt influenced by outside stresses)
What do you think??
Top of pagePrevious messageNext messageBottom of page Link to this message

Mikef5000
Posted on Monday, June 14, 2010 - 11:07 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Ok, so will welding the header make it strong enough, or do I need to buy a new one?

I had a header welded on a race car. It held just fine, and only cost $30 from a professional welding shop.

The big question to me is, how difficult is the remove/replace procedure, and what are the additional costs (non-reusable gaskets/straps/etc.)

If it only takes an hour and $20, get the thing welded. If it's a day long project, and takes $100 worth of additional crap (front straps are not reusable BTW), then I'd replace it with new, and not risk having to do it again.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration