G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through May 06, 2009 » Spark plug torque « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ronmold
Posted on Wednesday, April 29, 2009 - 07:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

How do you torque the front plug?
Top of pagePrevious messageNext messageBottom of page Link to this message

Svh
Posted on Wednesday, April 29, 2009 - 07:44 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I wouldn't. Heads are stripping left and right now... just kidding there are only 2 cases I have read on here Dr_Greg and Chrisrogers but I would hate it to happen to mine.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hmartin
Posted on Thursday, April 30, 2009 - 12:04 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Speaking of those posts, I've been a bit scared to know what I've done to my cylinder heads, too.

12 to 18 ft. lbs. is not much. I've changed many, many spark plugs in aluminum heads over the years, though, and I've always done 1/4 turn max. I've never had any problems, thank God, but I admit I've never measured it except by feel; I figure I'm applying torque to my socket wrench at 7 or 8 in. from the center, and right before 1/4 turn, it begins to feel like more than 20 to 25 lb. of force. I'm better at estimating pulling force than I am pushing force, but I've never bought a small enough torque wrench to know for sure, and now like you, I'm worried.

Can I turn the question around on you? How do you do it?

(Message edited by hmartin on April 30, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Hangetsu
Posted on Thursday, April 30, 2009 - 02:22 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Just turn until you feel the washer squish - no further.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ronmold
Posted on Thursday, April 30, 2009 - 02:29 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I tried to memorize the "feel" of the torque wrench I used on the rear at the same distance out that my open-end wrench is at the end, and tried to duplicate that feel. Very crude!
Top of pagePrevious messageNext messageBottom of page Link to this message

Svh
Posted on Thursday, April 30, 2009 - 05:07 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I turn until finger tight then a 1/4 turn. Have used it for 20 years since my grandpa taught me it. Not saying it is correct but never have stripped a head or had one back out.
Top of pagePrevious messageNext messageBottom of page Link to this message

Rwven
Posted on Thursday, April 30, 2009 - 06:39 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

And don't forget the anti-sieze
Top of pagePrevious messageNext messageBottom of page Link to this message

Seanp
Posted on Thursday, April 30, 2009 - 09:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Add me to the stripped head list. Be careful when you put the plug in - it's a hell of a surprise when it comes out violently, mid-ride...
Top of pagePrevious messageNext messageBottom of page Link to this message

Hmartin
Posted on Thursday, April 30, 2009 - 09:54 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Do you recall how far it turned it after you seated it? Was it more than 1/6th, or one full twist of an open wrench?
Top of pagePrevious messageNext messageBottom of page Link to this message

Ronmold
Posted on Thursday, April 30, 2009 - 10:03 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

about 2/6ths
Top of pagePrevious messageNext messageBottom of page Link to this message

Mnrider
Posted on Thursday, April 30, 2009 - 10:30 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

My 2 cents
Most of the cases I've seen of spark plugs coming out is from the spark plug not being tight enough.
You have to do more than just 1/4 turn past contacting the gasket.
All my years of installing spark plugs I've had 2 loosen up and they were both on snowmobiles were I didn't want to over tighten them.
The last 20 years or so I make sure the gasket is smashed and the plug is tight and I've never had 1 come out and I install spark plugs in alum. heads almost every day,so tighten that plug,you won't strip it
Top of pagePrevious messageNext messageBottom of page Link to this message

Bienhoabob
Posted on Thursday, April 30, 2009 - 10:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I couldn't find it in the Buell manual, but my sportster manual says:"If a torque wrench is not available, tighten it 1/4 turn after the gasket contacts the head."
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration