G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through January 30, 2008 » ECMspy bike connection? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Garyz28
Posted on Saturday, December 22, 2007 - 04:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I just got my cable in the mail today. Joel did a first class job putting it together. Thanks again Joel!

I haven't installed the software yet, but I went out to the bike to find where I plug the connector into. I found the ECM right on top under the seat, but I don't see a where the connector is. Can anyone tell me where to look?
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Saturday, December 22, 2007 - 05:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

It's just below the seat on the left hand side. It's a gray deutsch connector with a black rubber plug in it. You can get to it with the seat on. You might want to pull the seat and remove the headlight fuse while using the ecmspy.
Top of pagePrevious messageNext messageBottom of page Link to this message

Garyz28
Posted on Saturday, December 22, 2007 - 07:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Found it! Thank you!

Tonight I plan to load the program and then make a copy of the stock fuel maps etc. I want to study what I have right now for a bit before I start changing things much.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bertotti
Posted on Saturday, December 22, 2007 - 07:42 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Why would you remove the headlight fuse?
Top of pagePrevious messageNext messageBottom of page Link to this message

Gamdh
Posted on Saturday, December 22, 2007 - 08:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You need the ignition switch on for the ECM to have power. if you are connected for a while you could run the battery down.
Top of pagePrevious messageNext messageBottom of page Link to this message

Daveymac
Posted on Sunday, December 23, 2007 - 04:36 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You want as close to 12v for the proper functions of ecm.
I always pull the fuse!
Top of pagePrevious messageNext messageBottom of page Link to this message

Garyz28
Posted on Sunday, December 23, 2007 - 03:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

I have also heard it recommended to hook up a battery tender to the bike in addition to removing the headlamp fuse during a reflash.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jmhinkle
Posted on Monday, December 24, 2007 - 12:35 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Thanks for the compliments Gary. As far as pulling the light fuse, I always hooked up to battery tender and didn't mess with the headlight fuse. It was never on long enough to be that much of a problem that the tender wouldn't take care of quickly.
Top of pagePrevious messageNext messageBottom of page Link to this message

Gamdh
Posted on Monday, December 24, 2007 - 11:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

An interesting note... I pulled the fuse while I was resetting the TPS yesterday... the low beam still came on. I check the high beam and it did not work......

I have done the pin swap on the headlight connector so the low beam is always on... apparently that is on another fuse... or I'm just missing something?
Top of pagePrevious messageNext messageBottom of page Link to this message

Maximum
Posted on Monday, December 24, 2007 - 11:58 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Yup...that's the deal. I did the dual headlight mod by soldiering a jumper wire in the hi/low switch, but I did notice that the parking light was still on after pulling the headlight fuse.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Monday, December 24, 2007 - 12:12 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Try pulling fuse #5. It is the accessory fuse but it turned off my low beam as I did the conversion too. You can leave all other fuses in as long as you have the low beam on.
Top of pagePrevious messageNext messageBottom of page Link to this message

Twintour
Posted on Tuesday, January 01, 2008 - 02:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

-------------------------------------------------- ------------------------------
Hey Joel, are the cables plug and play , or do they need software driver to work? I have the ecmspy downloaded , do I need anything else beside your cable? I just want this for tps resets and basic trouble shooting ,if i stay away from the fetch and burn buttons is my ecm safe? If so do you have any cable ready to go. thanks Ray
Top of pagePrevious messageNext messageBottom of page Link to this message

Gamdh
Posted on Tuesday, January 01, 2008 - 08:20 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

You need the FTDI Virtual COM Port drivers

http://www.ftdichip.com/Drivers/VCP.htm

Oh, and do not try to install these until you have the cable in hand...


(Message edited by gamdh on January 01, 2008)
Top of pagePrevious messageNext messageBottom of page Link to this message

Twintour
Posted on Tuesday, January 01, 2008 - 11:22 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Thanks Ggmdh and Jmhinkle
Top of pagePrevious messageNext messageBottom of page Link to this message

Vagabond
Posted on Saturday, January 05, 2008 - 10:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

jmhinkle..............PM sent
Top of pagePrevious messageNext messageBottom of page Link to this message

Bobsims
Posted on Wednesday, January 16, 2008 - 03:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

Joel,

I got the cable this week -- first-rate job, thanks for the fast assembly and shipping. I installed ECMspy and the serial driver, and had it running and connected to the bike in no time. Wow, what a great asset, and what a great example of an open source hardware and software collaboration.

Thanks again, Joel, for providing the cable, for shipping to my APO address, and thanks also to the ECMspy team for putting together this tremendous piece of software.

Very timely, as well, as I think I had my first BAS cutout on the commute home from work today. :-)

Bob
Top of pagePrevious messageNext messageBottom of page Link to this message

Walrus2004
Posted on Sunday, July 04, 2010 - 06:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only)

how do i install the driver? my computer wont recognize the bike when the cable is connected... having a lot of trouble.

I tried downloading the driver and extracting it, but my computer and another computer is not recognizing the driver.

any tips?
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration