| Author | Message | ||
     Kruizen |
What has been the average for shipping these? | ||
| Stirz007 |
Kruizen - typically $30 to California, more like $40 east of Texasss. More for APO's or to Canadia. That's for one-week shipping. Double that for priority shipping. | ||
| Kruizen |
Thanks think this will be a fall purchase. Thanks | ||
| Stirz007 |
Kesnei - Please contact me when you can, RE: delivery of stand. Thanks JM | ||
| Kesnei |
Pm sent | ||
| Deanh8 |
You still have these? My motor just blew I think this would come in handy. | ||
| Rodrob |
Damn Dean! What happened? Is this the 1190 kit? | ||
| Stirz007 |
Dean - can do. PM'd you. | ||
| Stevel |
Thanks again Jeff. The stand finally arrived today. It looks great. | ||
| Dwp138 |
Forgot about these. PM sent | ||
| Stirz007 |
Steve - that's great! BTW, powdercoated option will not be provided by me. My guy was not as dependable as I had hoped. | ||
| Stirz007 |
Two available - bare metal or mystery paint - your choice! | ||
| Kruizen |
I'll take one-bare metal thanks | ||
| Stirz007 |
PM me your particulars (mailing address) please. Thanks JM  | ||
| Kruizen |
Pm sent | ||
| Bertman |
PM sent | ||
| Northernyankee |
Stirz you have a PM | ||
| Kruizen |
Haven't gotten a response from the pm I sent him yet. Anybody any ideas? | ||
| Stirz007 |
Responded to all this morning. Had some other stuff that needed attention, sorry. JM | ||
| Kruizen |
Jm didn't get anything. Ekruizenga@co x.net | ||
| Kruizen |
Thanks for the quick response. Paypal sent | ||
| Brandonbeals |
PM Sent | ||
| Terrys1980 |
Stirz I drew this up in paint. Any suggestions before I send to to a friend for fab?  | ||
| Stirz007 |
Terry - a couple of notes on what I have done. I reduced the overall length from 21" to 20". It worked fine, and saved a few bucks on shipping cost. For the yoke, the length of the flat bars is 3". I cut a 6" piece, drill both ends, then cut it in half. I use an angle grinder with cut-off wheel, so I lose maybe a bit over 1/16" OAL. The 1" square vertical piece is 8" long. For the rear, I start with a piece of flat bar 9" long. Drill one end to 3/8", the other end 5/8". Find the center of that bar and cut it in half at a 45 degree angle. The tube is just under 3-7/8" long. I think you could use 1" square tubing instead of 1-1/2", but I haven't tried it. If I did, the round tube would need to be shortened a quarter inch or so. (When in doubt, build it stout) | ||
| Terrys1980 |
Ok thanks. I will add some notes to my drawing. | ||
| Zac4mac |
Thanks for the drawing, very timely. I plan on bumping Loretta to 1190 this winter and a stand will simplify that process.. Z | ||
| Terrys1980 |
Here is a newer drawing using only 1" tubing.  | ||
| Frinzo |
Still making these? | ||
| Ducbsa |
I just have an XB and I am thinking of ordering one! | ||
| Northernyankee |
First off I wanted to say thanks to Stirz for posting up all the info to build these! Second don't mind my welding, I am a hack...lol. But I finally got around to fabbing up a stand since this winters maintenance is includes rebuilding the forks with new springs and valves for my weight and this will definitely come in handy. I still have to clean up some of my welds and throw a coat of paint on it, but for the most part its done. I ended up with plenty of left over materials so I can probably throw one of these together for anyone who lives close by.   |
