G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » Archive through July 24, 2016 » Braided oil lines... « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Charger22
Posted on Sunday, June 19, 2016 - 12:10 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Are they worth it or are there any advantages? And if so any one have a parts list of the fittings needed to complete the job?
Top of pagePrevious messageNext messageBottom of page Link to this message

Harleyelf
Posted on Sunday, June 19, 2016 - 12:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

In a system like ours, with very low pressure, the braid only provides protection from friction damage, such as the hoses that rub against one another under the engine of a tuber. They also will provide some protection from the heat of the exhaust.

This is useful, but not as useful as holding the shape of the hose under high pressure hydraulic or pneumatic use. Thus, the special fittings which make up most of the expense of proper braided lines are not really needed for motorcycle use.

JP cycles sells a kit with cut-to-length hose(use tin-snips) and decorative covers for the included regular screw-type hose clamps for about a hundred bucks.
Top of pagePrevious messageNext messageBottom of page Link to this message

651lance
Posted on Sunday, June 19, 2016 - 03:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I you want good stainless steel oil lines look at Goodrich. Years ago I had them make a complete set for the S2 and I fit perfectly and still holding strong. The OD of the line is much smaller then using stainless steel covered rubber lines.
Top of pagePrevious messageNext messageBottom of page Link to this message

Court
Posted on Sunday, June 19, 2016 - 03:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Kinda cool that Buell was the first motorcycle company to get approval from the feds to use braided line on a motorcycle.

Others had tried . . . but the "whip test" stopped them all in their tracks . . until Buell did it in 1990.

For more info:

http://www.badweatherbikers.com/cgibin/discus/show .cgi?tpc=4062&post=2109170#POST2109170
Top of pagePrevious messageNext messageBottom of page Link to this message

Harleyelf
Posted on Sunday, June 19, 2016 - 04:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've been quite pleased with my braided clutch cable. The stock ones all seemed to leak primary lube from the juncture of the sheath and the fitting - I had three fail. It's plastic coated so it won't scrub the finish off my left fork. Barely long enough for high bars.

lower.http://www.ebay.com/itm/231351804486?_trksid=p2060 353.m2749.l2649&ssPageName=STRK%3AMEBIDX%3AIT
Top of pagePrevious messageNext messageBottom of page Link to this message

S1owner
Posted on Monday, June 20, 2016 - 09:52 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Search my name and oil lines I have a whole howto with parts simewhere

Top of pagePrevious messageNext messageBottom of page Link to this message

Charger22
Posted on Tuesday, June 21, 2016 - 12:02 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks that looks awesome!
Top of pagePrevious messageNext messageBottom of page Link to this message

S1owner
Posted on Tuesday, June 21, 2016 - 03:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The fitting companies also make a fitting that has a hose clamp in it designed to slide over the braided hose its cheaper and simpler
Top of pagePrevious messageNext messageBottom of page Link to this message

Charger22
Posted on Thursday, June 23, 2016 - 10:58 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I was looking at those. They seem like they would provide a good look. Project on hold a little as carb rebuild just became a need. Float bowl is stuck....
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration