G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through July 09, 2013 » Going back to stock muffler-what's involved? « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through May 24, 2013Dmcutter30 05-24-13  09:49 am
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Dmcutter
Posted on Thursday, May 30, 2013 - 09:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The stock muffler arrived today and I ordered all the necessary mounting hardware from American Sportbike-should have it next Wednesday. I also checked and found that the cable for the exhaust valve is there. I assume the default position for the valve is closed, right? Can it be wired open with the cable installed or will it end up flopping out? I find this bike a pain to work on compared to all my in-line 4s and I just want to mount/connect things one time and put it all back together again. If it doesn't run well with the ECM programmed as is I will bite the bullet and ship it back to Buell, I guess.

Just out of curiosity, if the valve is really just for noise control at low rpm, what would happen if the valve was closed all the time?
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Friday, May 31, 2013 - 02:48 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If you're running the race ecm then I would wire the muffler open. I lightly crimped an electrical eyelet around the top of the cable and connected it to the furthest mounting screw for the actuator. I then adjusted the cable so it was fully open. I did this as a temporary fix until I got a new actuator. Later I found out that the valve is closed 90 percent of the time and just opens when you're in race mode with the throttle! With your ecm, having it open will work better and the sound is really nice yet not loud at all!
Top of pagePrevious messageNext messageBottom of page Link to this message

Dmcutter
Posted on Friday, May 31, 2013 - 02:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks. I will give that a shot.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ratbuell
Posted on Friday, May 31, 2013 - 04:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The valve is NOT for noise control. It changes the tuned length of the exhaust path to optimize low and midrange torque as well as high rpm horsepower.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Saturday, June 01, 2013 - 12:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If his EBR ECM was set up for a Jardine then it will work better with an open stock muffler than with a closed one. I would run the open stock muffler till Winter and then maybe send the ECM back to be programmed for the stock muffler, at which time you can hook it back up to the actuator.
If it runs fine with the open muffler then I'd probably just leave it alone!
Top of pagePrevious messageNext messageBottom of page Link to this message

Dmcutter
Posted on Tuesday, June 11, 2013 - 01:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Just picked up the bike from HD...I figured I would be money ahead paying someone to do the work since I have neither time nor patience...amazetron! The stock can is whisper quiet at idle and up to 3 grand, has some bark to it at 4k but still not as loud as the Jardine. Best of all the surge at constant throttle between 2 and 3k seems to be gone, although on the highway I didn't get to spend any time to speak of at 2-2.5k. I asked them to wire the valve open and assume it was done. I haven't had it over 4.5k yet so I don't know if there is a flat spot anywhere yet, but there is nothing below that. I am so pleased...guess I'll keep the beast now instead of going for the Hyperstrada (which I can't afford anyway...)
Top of pagePrevious messageNext messageBottom of page Link to this message

Jasonb
Posted on Wednesday, June 12, 2013 - 11:32 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I don't spend much time below 2.5k. I usually ride at 3-3.5. Under that, it shakes everything too much.

Thought that was normal. Is it not?
Top of pagePrevious messageNext messageBottom of page Link to this message

Dmcutter
Posted on Wednesday, June 12, 2013 - 01:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Shaking is normal, and it's lots worse at idle than above 2 grand, but mine was like a lean surge at constant throttle-jerky, not shakey.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration