G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » 1125R Superbike Board » Archive through September 29, 2014 » IAC Alternative « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Shawns
Posted on Saturday, September 06, 2014 - 08:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Is there an alternate part number like a Duralast? I found one a while back for an IAT.
Top of pagePrevious messageNext messageBottom of page Link to this message

Shawns
Posted on Sunday, September 07, 2014 - 05:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Bike won't idle for mrs than a few seconds. Have following codes
U0001 Comm Error
P0087 Fuel Pressure sensor low
P0193 Fuel Pressure sensor high
P0122 Throttle position sensor low
P0511 IAC fault
P0507 IAC RPM lower than expected
P0113 IAT sensor high or open

Fuel codes i have always had, readings from cluster say they are fine

TPS is new and IAC are new. I tried cleaning the IAC and did a TPS reset with the same results.

I am guessing IAC
Top of pagePrevious messageNext messageBottom of page Link to this message

Puddlepirate
Posted on Sunday, September 07, 2014 - 10:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Are you sure there's not more going on there than just the IAC? Do you have the troubleshooting section of the manual? A code by itself doesn't mean that the associated part is bad.
Top of pagePrevious messageNext messageBottom of page Link to this message

Rocketjump
Posted on Sunday, September 07, 2014 - 10:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Put the bike on a charger, low voltage can wreak havoc on your system. I had a bunch of error codes dumped from the ECM and put it on a charger overnight and presto, they were gone after 2 startups
Top of pagePrevious messageNext messageBottom of page Link to this message

Shawns
Posted on Sunday, September 07, 2014 - 10:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Scratch the IAC, it is moving so I don't think its that. I have the manual(several actually). I am going to try and eliminate one code at a time. Don't have ecmspy, couldn't download a copy that would work. I do have the cable tho. The TPS diag in the electrical manual looks like an ECM or throttle body assay. I have an EBR ecm so replacing that will be costly and would put me out for the rest of the season. I put the bike on a tender every night when done riding and don't remove it till I ride next. After I reassembled everything and tried to restart the bike, it was a hard start and backfired a little. Finally got it to start and it idled for a few seconds and stalled. It was easier to restart after that tho.
Top of pagePrevious messageNext messageBottom of page Link to this message

Figorvonbuellingham
Posted on Monday, September 08, 2014 - 10:19 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Haven't had to do much to my Buell yet, but I have my Aprilia. The throttle bodies have to be synchronized on it. I don't know how you do it on an 1125, but may be worth looking into. Also, you can spray some carb cleaner down the iac to get the build up off of it. Just because its moving doesnt mean its moving right. It might be partially obstructed. That little motor doesnt have alot of torque. I actually took mine apart (on the Aprilia) and cleaned the drum by sticking it in a drill and hitting it with some 1100 wet sand paper. Worked great after that.

(Message edited by figorvonbuellingham on September 08, 2014)
Top of pagePrevious messageNext messageBottom of page Link to this message

Rodrob
Posted on Monday, September 08, 2014 - 03:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Check your grounds.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration