| Author | Message | ||
     Buellish |
All prices include shipping in the US. See pics at: http://s1120.photobucket.com/albums/l500/buellish1 /Tuber%20Parts/ X1 carbon fiber tank accents.Install when you remove the left side scoop and airbox.American Sport Bike sells these for $289.I'd like $160 X1 fly screen.flat black,could use a repaint or use as is. $50 X1 tank cover,paint same as above. $75 X1 tank cover,Blue Racing stripe.Some small scratches. $75 X1 chin spoiler,I'm removing a couple of scratches with filler,should be done tomorrow,paint flat black as above $60 X1 front forks complete with tripple trees and upper handlebar clamp.Some damage to the coating $275 S1 forks,forks only $130 X1 dash with gauges and ignition switch w/key. $75 X1 tail complete. $70 X1 headlight. $40 X1 headlight fork mounts $35 shipped See pics at: http://s1120.photobucket.com/albums/l500/buellish1 /Tuber%20Parts/ Thunderstorm heads,need reworking. $135 X1 bottom end with bad bearing. $150 Complete clutch, $180 Clutch ramp $20 Shift shaft $20 Clutch adjuster w/release plate $30 shipped Regulator $20 Rotor $60 Stator $60 Regulator $35 Econowinder with K&N knockoff $30 Primary cover black wrinkle $100 X1 harness $45 X1 Banke shifter & brake lever.Brake lever is broken but could be welded $100 Peg mounts front and rear w/one pair of pegs $35 Left side handlebar control $35 Right side handlebar control w/throttle & idle cables and pair of grips $50 See pics at: http://s1120.photobucket.com/albums/l500/buellish1 /Tuber%20Parts/ Clutch perch w/lever $25 X1 intake manifold w/injectors $65 X1 race module part number N1306.K $125 X1 coil $30 Long stem front signals $20 X1 seat release $20 X1 seat $75 Stock muffler mount $15 Derby cover,needs a polish $20 61 tooth pulley $35 Front axle w/spacers,washer and nut $35 Rear axle w/spacer,adjuster plates,washer and nut $55 Front Nisson caliper w/good pads $50 Rear Nisson caliper w/mount and good pads $40 Front Goodrich braided hose $30 Front wheel w/new bearings 1500 mi ago,black with some scratches but overall a good looking wheel $115 See pics at: http://s1120.photobucket.com/albums/l500/buellish1 /Tuber%20Parts/ Rear wheel w/new bearings 1500 mi ago,black with some scratches overall a good looking wheel $170 Rear white wheel with powder coat removed from rim about 1 1/4" in,some scratches,needs a polish $150 Front Marchesini w/original rusty rotor,rounded out fasteners on rotor,white with scratches $80 '02 X1W header,previous owner said pipe was wrapped to cover blue header.I've not removed wrap. $180 Vance & Hines SS2R for X1 in rough shape,some damage to mount $50 X1 oil tank $30 | ||
| Outdoors |
Dibs on the x1 dash with guages and the x1 headlight/fork mounts. Pm sent also. | ||
| Thejuicer |
Pm sent on the heads. | ||
| Jolly |
please send photos of banke shift and brake, if the only damage is the brake pedal, I think I have one of those, so id like to see the the shifter assembly. are all pieces there?? can I call dibs with a caveat.??? is that even fair on any level???? | ||
| Jolly |
Dibs, Im in for the Banke pieces, at first look the photo bucket wouldnt load...PM me for payment and shipping. (is all hardware there, couldnt tell in the photo) | ||
| Buellish |
Jolly,the link seems to be working fine.All the bits are included with the Banke shifter. | ||
| Matrim |
PM sent for CF accents. | ||
| Buellish |
Banke shift and brake levers are sold. | ||
| Dutch_x1 |
Pm send on vance&hynes | ||
| Matrim |
Payment sent for CF accents. | ||
| Buellish |
Carbon fiber accents are sold. | ||
| 99cyclone |
Are the heads sold? | ||
| Buellish |
"Are the heads sold?" No not yet. | ||
| 99cyclone |
What work is needed on the heads? I could use a pair for my S1. | ||
| Madmacks |
"bottom end with bad bearing" which bearing and what all comes with the package? | ||
| Buellish |
"What work is needed on the heads?" The tech that diagnosed the bottom end said the heads were useable but would probably need going through.They look pretty good to me,if a bit carboned up. Look here" http://s1120.photobucket.com/albums/l500/buellish1 /Heads/ | ||
| Buellish |
The bottom end has a bad big end rod bearing and would come with the cases,rotating assembly,rods,pistons and oil pump. What of the rotating assembly is useable,I don't know. | ||
| 99cyclone |
Thanks...I'll take the heads. Do you accept PayPal? If so, please PM me your info. | ||
| Buellish |
Joe,PM sent. | ||
| S2pengy |
Mike E mail me about the WP forks please | ||
| Buellish |
Todd,PM sent. | ||
| Firstbuell |
I'm in for the $25 clutch perch & lever ready to PayPal..... | ||
| Buellish |
Thunderstorm heads are sold. | ||
| Buellish |
Clutch perch and lever is sold. | ||
| Madmacks |
PM sent on the bottom end | ||
| Dwrecked |
Hi would you be willing to split the wp forks up? | ||
| Buellish |
The S1 forks are no longer available. | ||
| Buellish |
I have a few more parts to list. '99 aluminium swingarm with mounting block $125 Upper engine mount $20 Front isolator mount $40 Three tie bars with spacers $35 Rocker covers complete with rockers could use a polish $50 | ||
| Ltbuell |
Buellish,sent you a pm. | ||
| Jolly |
hows the condition of the swingarm? does it include the axle, adjustment blocks etc? looked on the photos and didnt see the swing arm. have been wanting to change the swingarm on my s1 to an x1...just need the parts, time and .... |
