G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » M2 Cyclone » Archive through April 02, 2009 » Oil Pump drive bronze gear "loose fitting" « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Hugie03flhr
Posted on Thursday, March 26, 2009 - 10:54 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hey everyone, I finally pulled my 02 M2 apart to replace my drive gear with a bronze race gear. When I slipped the gear on the pinion shaft I expected a snug fit. The gear just slid on w/ a slight wiggle. I would say it has about .003-.005 clearance between pinion shaft OD to bronze gear ID. Is this correct?
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Thursday, March 26, 2009 - 02:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The later engines are made to take apart with out PULLERS ...

Make sure you TORQUE the pinion shaft nut(& RED locite)to 70 ft. lbs and not the 35 to 45 ft. lbs as in the FSM !!!

(Message edited by buellistic on March 26, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Hugie03flhr
Posted on Thursday, March 26, 2009 - 04:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Now ya tell me!!! Just kidding Thanks for the info. Well I did use RED Locite and torqued it to the higher side of 45 ft.lbs. I installed the 2007-08 Oil Pump w/ the Bronze gear so I'll have both gears new but I was concerned about that looseness so I used Red Locite on that too

(Message edited by hugie03flhr on March 26, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Sleez
Posted on Friday, March 27, 2009 - 01:57 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Buellistic:

where does that torque spec come from?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hugie03flhr
Posted on Friday, March 27, 2009 - 08:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The 35-45ft lbs. comes from the manual but doing some research some wrenches torque it to 70ft lbs. too make sure it don't come lose. I'm going to post this on the tuber forum, to see if anyone else notice the loose gear fitting.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Friday, March 27, 2009 - 09:10 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Sleez:

From www.nrhsperformance.com, CAMSHAFT INSTALLATION ...
Top of pagePrevious messageNext messageBottom of page Link to this message

Sleez
Posted on Friday, March 27, 2009 - 11:19 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

thanks
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration