G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Old School Buell » M2 Cyclone » Archive through December 31, 2008 » Dead in the water « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

00cyclone
Posted on Wednesday, November 05, 2008 - 03:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Came out this morning to ride to school. Did everything i normally do then hit the starter and....nothing. Battery was fully charged and everything. I can hear a click near the motor when i hit the start button but thats all that happens. Already checked the obvious stuff like spark plugs wires connected, kill switch in on position, even with the side stand up and still nothing...I have a feeling its something small and im just not thinking of it. Ideas?
Top of pagePrevious messageNext messageBottom of page Link to this message

Tripp
Posted on Wednesday, November 05, 2008 - 04:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

try jumping the clutch switch, i've had two fail on me, jumped it and no problems since, unless i start her in gear of course!
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellfighter
Posted on Wednesday, November 05, 2008 - 04:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Check the cables to the battery with a wrench to make sure they are tight.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellistic
Posted on Wednesday, November 05, 2008 - 04:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Just because the BATTERY shows a correct full charged battery reading does not insure the CRANKING AMPS/VOLS are high enough to start the engine ...

(Message edited by buellistic on November 05, 2008)
Top of pagePrevious messageNext messageBottom of page Link to this message

00cyclone
Posted on Wednesday, November 05, 2008 - 05:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Its a brand new battery and i had it on the battery tender all night. Havent ridden it in like a week or so because of the rain and then i came out to ride today and nothing...How do you jump the clutch switch? Ive noticed that mine flickers sometimes so maybe thats it
Top of pagePrevious messageNext messageBottom of page Link to this message

Koz5150
Posted on Wednesday, November 05, 2008 - 05:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Check your grounding strap between the frame and the rear swingarm (on the frame side). There is a small washer that if rusted will prevent your bike from getting enough juice to start.

I found this when mike bike would randomly not start, usually after being parked outside overnight or after driving in the rain. After cleaning the connection I replaced the washer with a stainless one 3 years ago. I have not had a problem since.
Top of pagePrevious messageNext messageBottom of page Link to this message

Koz5150
Posted on Wednesday, November 05, 2008 - 11:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Forgot to mention, this will also prevent your bike from charging the battery properly! This would make you think it could be a battery, stator, or other electrical issue.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tripp
Posted on Thursday, November 06, 2008 - 10:42 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

to jump clutch switch, use 2 alligator clips connected by a wire, pull the plug at clutch lever clip the alligator wire to both sides of plug.
Top of pagePrevious messageNext messageBottom of page Link to this message

Littlebuggles
Posted on Sunday, November 09, 2008 - 01:18 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If it's not the clutch safety switch jump the wires on you sidestand safety switch, plenty of people have had trouble with those. I second Koz on a check of the ground strap, and Buellfighter and battery cables since you just replaced that.

Let us know what you find when you get her going.
Top of pagePrevious messageNext messageBottom of page Link to this message

00cyclone
Posted on Sunday, November 09, 2008 - 05:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It was the starter relay. I could hear a clikcing sound coming from the rear end and i traced it to the relays. Second one to go out on me in about 3 months which is weird. I think they were the stock ones though...Thanks for your help though guys i do appreciate it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Koz5150
Posted on Monday, November 10, 2008 - 11:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I think you can buy one of those button type that I think would allow you to start the bike if that popped up again.

Look here

http://www.jpcycles.com/productgroup.aspx?GID=2853 E63F-DDAF-4D29-9C27-09EA09CE013D

Might be worth checking out.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration