G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Knowledge Vault (tech, parts, apparel, & accessories topics) » Do It Yourself: Machine Shop, Garage, Tools and Tips » Archive through October 09, 2009 » Tools to remove/install wheels « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Shaiss
Posted on Monday, October 15, 2007 - 02:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Can anyone tell me the hex size needed to remove the front & rear axles/wheels?

I need to take of both wheels, so need to know what size hex key to buy on the way home and I dont have the manual on me.

Are there any other tools I need?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hexangler
Posted on Monday, October 15, 2007 - 02:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm not sure of the exact size, but there is a special tool (a gold partitioned hex bar about 1.5" long) included in the tool pouch. Have you lost yours?
Hex
Top of pagePrevious messageNext messageBottom of page Link to this message

Shaiss
Posted on Monday, October 15, 2007 - 03:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have that, but thats to remove the pinch bolt in the rear axle right?
Top of pagePrevious messageNext messageBottom of page Link to this message

Shaiss
Posted on Monday, October 15, 2007 - 03:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ignore my last comment, Im retarded and just figured out what you were saying
Top of pagePrevious messageNext messageBottom of page Link to this message

Hexangler
Posted on Monday, October 15, 2007 - 04:04 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

This is for the XB correct? I don't have my digital camera here, but the axle tool in my tool pouch (as measured with a tape measure) is a gold hollow hex bar stock 1 inch long and 7/8 inch across the flats (it also has a circlip in the center to prevent the tool from inserting too far into the axles). You will need some standard Allen wrenches to loosen the pinch bolt (rear) and pinch bolts (front). The axle "nut" special tool goes in the hex hole on the end of each hollow axle, then you can loosen the axle with the protruding "nut" with a Crescent wrench. The front axle is left hand thread, rear is right hand thread. The rear axle is backed out 20 full turns which allows the axle to loosen the drive belt because the axle is stepped (ingenious). For reassembly, I greased both axles with BelRay waterproof (because I was getting corrosion on the shafts), and I used AntiSeize on the threads.
Hope this helps,
Hex
Top of pagePrevious messageNext messageBottom of page Link to this message

Hexangler
Posted on Monday, October 15, 2007 - 04:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I type slow...
Hex
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration