G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through June 21, 2018 » Both headlights out - any quick checks? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Jdubxb
Posted on Wednesday, February 28, 2018 - 09:18 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The 15A fuse for "lights" is intact. Tried swapping with the spare fuse but no difference. Also tried swapping the Aux and Start relay positions. The high beam indicator turns on and off with the switch. I'm not at home now so do you have any suggestions for a quick check?
Top of pagePrevious messageNext messageBottom of page Link to this message

Zacks
Posted on Wednesday, February 28, 2018 - 09:58 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Other than the obvious - and unlikely - both bulbs are burned out...
Looking at the schematics, the common point is the 38A connector.
I'd check to make sure there's good contact where the headlights plug in.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jdubxb
Posted on Wednesday, February 28, 2018 - 10:05 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Both headlights were working just yesterday so I doubt both would burn out so close in time. I don't have tools to take the fairing off at this time.
Top of pagePrevious messageNext messageBottom of page Link to this message

Bottlefedbuell
Posted on Wednesday, February 28, 2018 - 10:14 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

There is a (white, i believe) connector under the fairing you should be able to access.
Sometimes one of the pins (ground usually) gets a little pinched and will not complete the circuit causing both to go out.
You may have to get in there with a pick and carefully spread the prong to get a better connection.
This is also where you perform the 'both headlights on' mod, if havent already.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Wednesday, February 28, 2018 - 10:38 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Turn it to high beam. Does the indicator show?

If so, it's probably a broken ground at the steering neck.
My XB12X loves to pop grounds.
Low bid wiring harnesses I guess.

Test this theory by running a wire from the chassis ground or negative battery terminal to triple cla
Top of pagePrevious messageNext messageBottom of page Link to this message

Jdubxb
Posted on Wednesday, February 28, 2018 - 11:55 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The high beam indicator turns on and off with the switch. Everything else seems to work, so it looks like I will have to wait until I get home to remove the fairing (firebolt)
Top of pagePrevious messageNext messageBottom of page Link to this message

Bottlefedbuell
Posted on Wednesday, February 28, 2018 - 12:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

you shouldnt need to remove fairing. Everything is accessible from the underside.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Wednesday, February 28, 2018 - 12:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If both bulbs are burnt, it is likely a failing voltage regulator causing high voltage spikes
Top of pagePrevious messageNext messageBottom of page Link to this message

Jdubxb
Posted on Wednesday, February 28, 2018 - 12:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'll measure the voltage with the motor running, when I get home. Thanks for the tips.
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Wednesday, February 28, 2018 - 02:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If you start the bike with both on, and the battery is bad, it can cause the bulbs to pop, had a bunch of that on mine and ended up putting a time delay relay on them so they wait 30 seconds before the lights come on. (modded headlights)

But I'm betting on the ground between the frame at the headstock and the first connector.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ffbuell1
Posted on Wednesday, February 28, 2018 - 04:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hi Check the small wiring harness that branches off to the headlights, I have replaced mine twice over the years.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jdubxb
Posted on Wednesday, February 28, 2018 - 06:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

How long is that harness (on a firebolt)? Do you think I could bypass it with some wire and spade connectors until the ordered part arrives?
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Wednesday, February 28, 2018 - 10:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Talk about a kick in the beans : )

I was just in the garage to get something and thought I would take a quick picture of the location of my persistent failures.
Look what I found when I turned the bars to the right:

eg


I guess It happened just as I turned the bars that one last time.


The big ugly red wire is my addition. It goes between the frame and the upper triple clamp. That was one of my failure points and the other is as you see in the picture.
That little clusterF*** goes to the blinkers and the headlights. I guess I'll have to find out what my new mystery wire goes to.

Awesome bike; TERRIBLE wiring harness.
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Wednesday, February 28, 2018 - 10:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I think there are 4 black wires in 2 connectors.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jdubxb
Posted on Thursday, March 01, 2018 - 10:19 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Both bulbs are burned. Voltage at 14.35 at startup fast idle, which seems normal. Should I have measured at higher rpm? Maybe just bad timing with both bulbs going out on the same day? I had a spare H3 bulb and it fired up when I plugged it in.
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Thursday, March 01, 2018 - 10:46 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

When the VR starts to fail, the voltage can intermittently spike high enough to burn out the bulbs. You are not likely to see it happen watching a meter on your battery for a minute, you would need something setup on your bike to monitor the voltage. On my last VR failure, I would see my aftermarket meter start flashing its high voltage warning in the middle of a ride and the headlights would get much brighter.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Saturday, March 03, 2018 - 09:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yep, my stator failed which took out the VR which kept blowing my headlights. Replaced VR and it did it again because I didn't check the stator. So if you find the VR bad do all the test on the stator. If it fails just one of the test it's toast. Don't ruin another VR, check the stator.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration