G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through June 21, 2018 » Fork Springs « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Aschem
Posted on Wednesday, November 01, 2017 - 10:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Any estimate on how many miles before fork springs need to be replaced on an XB with 43mm forks?
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Wednesday, November 01, 2017 - 11:30 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've never heard of them wearing out. If someone is replacing them, it is usually for a different rate or crash repair.
Top of pagePrevious messageNext messageBottom of page Link to this message

Shoggin
Posted on Wednesday, November 01, 2017 - 11:57 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Theres no service interval for fork springs, and I've never heard of a set wearing out.

But I'd highly recommend getting the right set for your fully geared and loaded weight, and your riding style.
Top of pagePrevious messageNext messageBottom of page Link to this message

Aschem
Posted on Thursday, November 02, 2017 - 08:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks, i thought I read in he service manual something about spring height and if shorter than recommended, then replace. Appreciate the fast replies.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skipbarberman
Posted on Thursday, November 02, 2017 - 09:46 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Fork Springs are coil springs, and by design, don't wear out, per se. They are heat treated and based on metallurgical design, will not wear out unless they come in contact with something and wear out or fail based on abrasion or fracture. Generally, coils can't be over or hyper-extended like a leaf, as they coil bind or stack, physically protecting them from type of failure. If you were racing at the highest levels, perhaps you could tell the difference. Or, measuring spring rate with an instrument on the same set of coil springs over a LONG period of time. As for riding on them in forks, 99% of the riders would never pick up on a 1 pound difference.
As stated by Froggy, different spring rates or progressive rates, are typically the only reason to change them. Another old trick is to remove some of the coils (hack saw) for various reasons I won't go into here, and while that might change the free spring height, it won't change the rate. Hope this helps.
Top of pagePrevious messageNext messageBottom of page Link to this message

Shoggin
Posted on Thursday, November 02, 2017 - 11:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Removing coils from a coils spring does change the free height of course. It also definitely raises the spring rate.
Think about untwisting a coil until it's straight (a torsion bar). The shorter it is, the harder it will be to twist.

If you want to lower the forks and keep the spring rate stock, use a different height spacer tube and plan on addressing the rear suspension or deal with rake changes that will make the steering drastically quicker and more unstable (to some, that's a good thing). Remember a Buell already has one of the tightest angles already!


And a note on cutting them with a hacksaw:
Fork springs almost always have closed coils top and bottom. If you were to chop some off, that leaves an very weak open coil that has to over compress before contacting the rest of the stack. Pre-load isn't enough to do it.
That means, what used to be a predictably slow spring rate increase, now starts at a much lower rate that increases drastically higher than stock very quickly. On a sportbike fork that sees a couple inches of travel only, thats a big deal.

Like anything handling, opinions vary for whats "good" and "bad". Only your personal confidence level and lap times really count
Top of pagePrevious messageNext messageBottom of page Link to this message

Skipbarberman
Posted on Friday, November 03, 2017 - 07:10 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yeah, what he said.
Top of pagePrevious messageNext messageBottom of page Link to this message

Shoggin
Posted on Friday, November 03, 2017 - 07:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Sorry I got wordy... I'm a suspension dork: )

Top of pagePrevious messageNext messageBottom of page Link to this message

Skipbarberman
Posted on Friday, November 03, 2017 - 08:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Me too, but you did a better job.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mhlunsford
Posted on Thursday, November 30, 2017 - 05:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I would recommend checking the fork oil level and valve adjustment unless you know the spring rate is wrong for you weight.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration