G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » 1125R Superbike Board » Archive through May 12, 2018 » How to Interpret the Fuel Map from xprfuelmapextractor « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

1life2live
Posted on Monday, April 23, 2018 - 09:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've also been trying to read up from everyone on how they can interpret and tweak the fuel map similar to the various threads on increasing the engine breaking parameters while running the EBR racing ECM.

When I compare my original ECM XPR file vs the EBR racing ECM XPR (stock exhaust), they appear the same to me.

Here is the Original Fuel Map:

Original XPR Fuel Map


Here is the EBR ECM Fuel Map:

EBR XPR Fuel Map


Additionally, when I use the Compare feature in TunerPro RT with the EBR XPR loaded, and the Compare with the Original XPR, it isn't showing anything different (comparing the Map 3D Fuel Front and Rear). But the bike behaves totally different front the stock ECM including the reduced engine braking...so I obviously need to continue researching this.
Top of pagePrevious messageNext messageBottom of page Link to this message

Barraspalding
Posted on Monday, April 23, 2018 - 10:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

From within ECMdroid i see numbers change between the original stock tune and the race tune i received.

I'll be downloading this xpr tool shortly
Top of pagePrevious messageNext messageBottom of page Link to this message

Stimbrell
Posted on Tuesday, April 24, 2018 - 02:44 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

The engine braking is controlled by the idle rpm in gear with the clutch out which is higher than idle in neutral. The higher the rpm the less engine braking, it is like not closing the throttle all the way. Where this setting is though I do not know.
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Tuesday, April 24, 2018 - 02:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Engine braking can be controlled by the amount of fuel is the last two rows. I would raise all the ones below 40 to at least 40. That is how we used to control it on the XB. Too much fuel will result in popping under decel.


Top of pagePrevious messageNext messageBottom of page Link to this message

Stimbrell
Posted on Tuesday, April 24, 2018 - 03:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

All that will do is make the bike run rich under those conditions, not alter the engine braking, that is the same as increasing the pilot jet in a carb bike, does not affect engine braking at all, the bike does not know clutch is out or bike is in gear.
Top of pagePrevious messageNext messageBottom of page Link to this message

Alex
Posted on Wednesday, April 25, 2018 - 02:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Gentlemen,

engine breaking on the 1125 is not controlled via fuel in the main fuel tables or the set idle rpm. There are specific tables that control engine breaking. These tables handle the IAC stepper motor as the main parameter to control engine breaking as this is the system that can override Your closed throttle by simply bypassing the air around the throttle blades. There are some parameters that can / need to be set right and from what I remember two tables (alternately selectable through a config byte) that deal with the IAC position at closed throttle deceleration. We had the same problem with our race bike as delivered from EBR back in the Pegasus Race Team days so I had to adjust it. Basically no engine breaking. Unfortunately it is too long ago for me to remember all the details but the IAC is the major player within engine breaking for sure.

Regards

Alex
MTeK Engineering
Top of pagePrevious messageNext messageBottom of page Link to this message

1life2live
Posted on Wednesday, April 25, 2018 - 08:28 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks everyone for your inputs! I also double checked the IAC Setpoint table between the original file and EBR file and they are identical as well. So, I'm now assuming like Alex stated that there must be more to this than the fuel map and the AIC setpoint table....back to square one.
Top of pagePrevious messageNext messageBottom of page Link to this message

Stimbrell
Posted on Wednesday, April 25, 2018 - 09:51 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Alex
Thank you for that information and if you ever recall how it is adjusted please post, this has come up a few times but never how to make the adjustment.
Top of pagePrevious messageNext messageBottom of page Link to this message

Alex
Posted on Wednesday, April 25, 2018 - 01:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Steve,

You could come over from the UK to good old Germany and I could probably find out again what needs to be done .
It is not too easy without a bike as I would probably have to test some things and I donīt have a 1125 here. Are You using the IDS software? This might be an option. Iīm using the IDS software quite exclusively and if You can read out Your current data with the IDS I may take a look at it if You want and see if I can help You.

Regards

Alex
MTeK Engineering
Top of pagePrevious messageNext messageBottom of page Link to this message

Stevel
Posted on Thursday, April 26, 2018 - 04:55 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Alex,
I am confused. Are you saying that the IDS software is capable of changing stored data and settings on standard ECMs? There may be a definition problem here. What many folks call EBR race ECMs are standard ECMs with different maps. As opposed to the true race ECMs that were completely changeable by the IDS software.
Top of pagePrevious messageNext messageBottom of page Link to this message

Stimbrell
Posted on Thursday, April 26, 2018 - 05:39 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That is an eleven and a half hour journey each way Unfortunately I am using the Tunerpro RT software. I spent some time last night looking at this again and I will test a few settings and see if I can work it out. Thanks for the offer to look though.
Top of pagePrevious messageNext messageBottom of page Link to this message

Alex
Posted on Thursday, April 26, 2018 - 06:53 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Stevel,

basically every Buell ECU is an IDS ECU - no matter if it is labeled standard or race - and the IDS software can work with all IDS ECUs. Still You need specific data and administration rights to make it happen .

Stimbrell,

sounds like a real long journey, so You might be better off trying to play with the RT software. Best of luck.

Regards

Alex

(Message edited by Alex on April 26, 2018)
Top of pagePrevious messageNext messageBottom of page Link to this message

Stimbrell
Posted on Thursday, April 26, 2018 - 10:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Here is what I am looking at the moment, the 2nd entry for load 11, 2200 rpm is what my bike does at clutch out with no throttle in first. Anybody tried adjusting these values? if not I will give it a go. The compare bin shown in the graph in red is the stock ecm setting.


Tunerpro screen shot
Top of pagePrevious messageNext messageBottom of page Link to this message

Alex
Posted on Thursday, April 26, 2018 - 02:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I donīt think Youīre looking at the right table. This table defines the region where deceleration correction (probably fuel and maybe spark) will take place. If the engine is operated below the defined line (that is if load is less than the given number above each engine rpm) the engine is in deceleration mode and appropriate corrections are made (for example I see in the search window of RT in Your picture that there is a value called Deceleration Correction. My guess is it holds fuel correction values). If You change numbers in the Deceleration Correction Region table all You do is alter the shape of the region where deceleration corrections are applied. You could try to change values in the Deceleration Correction table to alter the effect that takes place within the deceleration region but I doubt that it will massively influence the engine breaking. As I said, the major player is IAC position during deceleration. Iīm not sure if RT will show You the necessary tables at all as I donīt think that RT will give You all the tables and parameters that the IDS software can show.

Regards

Alex
Top of pagePrevious messageNext messageBottom of page Link to this message

Stevel
Posted on Thursday, April 26, 2018 - 02:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

What Alex is saying is the issue is air not fuel. By reducing manifold vacuum, the engine deceleration force will be reduced and it is the IAC that passes that air. The amount of air that passes through the IAC is a product of a valve that is controlled by a stepper motor. The table Alex is referring to is the table that controls the pulse count that goes to the IAC stepper motor.
Top of pagePrevious messageNext messageBottom of page Link to this message

Alex
Posted on Thursday, April 26, 2018 - 03:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

That is correct, Stevel.

Stimbrell,
do me a favor and show me screen shots of the following RT tables:

Map 3D: Running (Gear)IAC Position Map and
Map 3D: Running (RPM) IAC Position Map

Regards

Alex
Top of pagePrevious messageNext messageBottom of page Link to this message

Stimbrell
Posted on Friday, April 27, 2018 - 05:41 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Here you go and thanks for looking at this. The deceleration correction is just a %. 95 in the race ECM and 100 in the stock. I will give that a try as well.


Tunerpro screen shot 2
Top of pagePrevious messageNext messageBottom of page Link to this message

Barraspalding
Posted on Friday, April 27, 2018 - 08:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm loving all this... keep up the collaboration efforts fellas : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Thefleshrocket
Posted on Friday, April 27, 2018 - 12:36 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have an EBR Barker tune with the stock engine braking. Would that be helpful to compare to the stock tune?
Top of pagePrevious messageNext messageBottom of page Link to this message

Alex
Posted on Friday, April 27, 2018 - 02:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Stimbrell,

meanwhile I looked in the RT software, too (I have looked at it some years ago and reloaded it now). I find pretty similar things compared to what You showed me. I played around with it and for me it looks like RT may mix up some things although I canīt say for sure. RT and IDS for example show some different behaviour when changing axis values and other things. So this is the point where I canīt help You any further as I donīt want You to have some unexpected results based on my advice. I hope You donīt mind.
In the setup I used for our race bike the "Running (RPM) IAC Position Map" (which has a different name in IDS) was the one that I modified. It tells the IAC stepper motor which position to take based on rpm and engine temperature above idle.

Regards

Alex
Top of pagePrevious messageNext messageBottom of page Link to this message

Stimbrell
Posted on Saturday, April 28, 2018 - 04:21 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Alex

I do not mind at all, thank you for your help, I now have some options to try going forward. Thefleshrocket, I will get in touch if I need to look at that if that is OK.

Regards
Steve

(Message edited by stimbrell on April 28, 2018)

(Message edited by stimbrell on April 28, 2018)
Top of pagePrevious messageNext messageBottom of page Link to this message

Barraspalding
Posted on Tuesday, May 08, 2018 - 07:25 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Keeping this thread alive in hope that someone will be a smartypants and have a resolution that can be explained to me
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration