G oog le Buell 1125R Forum | Login/out | Topics | Search | Custodians | Register | Edit Profile


Buell Forum » 1125R Superbike Board » Stator/Voltage Regulator/Charging System subforum » High RPM voltage overflow « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Beefsupreme
Posted on Saturday, May 31, 2014 - 07:34 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So I have the CB605SB. And Rick's Stator. And the EBR rotor. *only under load* above like 9k rpm, I get overcharged. If I cruise and slowly bring the RPMs up it reads 14.0V (with high speed fans on) all the way to redline. If I'm gunning it, the dash shuts off and displays system voltage.

I thought I was done with this shit.
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Saturday, May 31, 2014 - 09:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

several folks have the 605 perhaps if this has recently started you have a connection issue perhaps grounding?
Top of pagePrevious messageNext messageBottom of page Link to this message

Dhays1775
Posted on Saturday, May 31, 2014 - 09:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

There has been talk from the previous threads I've found that indicate the CE605SB can be bad out of the box. I also have the same VR that you do.

I also have a spare good stock VR if you want it, just cover shipping and it's yours.

As for the dash shutting off, it is most likely a bad connection. I was helping a fellow Buell 1125 rider troubleshoot his R. With the VR plugged in, it would shut off the dash from presumably high voltage. Unplug it and it would light back up.

Good luck, and please keep us posted.
Top of pagePrevious messageNext messageBottom of page Link to this message

Beefsupreme
Posted on Sunday, June 01, 2014 - 02:59 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I emailed Jack Fleming of Roadster Cycles where I bought the V/R, he had this to say

Hi, I’ve heard of it now and then popping up. I suggest sending it back to Cycle Electric with a note when you bought and what it’s doing. They are really good about warranty
issues. The only thing that Cycle electric suggested once was making sure all your battery connections are good, solid and clean. He told me that if you have a bad connection at the battery it could cause an intermittent spike. I would also try to bypass the circuit breaker by putting both wires on one post of the circuit breaker and try that.


Jack

I'm going to bypass the breaker, for some reason I feel like that may work. If not, sounds like I'm sending it back in.
Top of pagePrevious messageNext messageBottom of page Link to this message

Beefsupreme
Posted on Monday, June 02, 2014 - 10:56 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Well so far so good, seems to have fixed it. I'll have to rip it open a few more times but today I did twice and had zero issue.

I shouldn't need a fuse there right?
Top of pagePrevious messageNext messageBottom of page Link to this message

Oldog
Posted on Monday, June 02, 2014 - 03:00 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Beef the CB is a self re seting device if the wire movement resolves the issue, replace the CB
Top of pagePrevious messageNext messageBottom of page Link to this message

Beefsupreme
Posted on Monday, June 02, 2014 - 03:19 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm wondering if the vibration of the bike under load is causing momentary disconnect within the cb. It's the only thing I can think of since it doesn't happen any other time
Top of pagePrevious messageNext messageBottom of page Link to this message

Sparky
Posted on Monday, June 02, 2014 - 10:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If the VR includes a circuit breaker, I would think that vibration would more adversely affect an electro-mechanical device like a circuit breaker that is in series with the VR and not affect an all electronic device like the VR.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration