G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » Archive through April 14, 2017 » Parts numberspassword « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Lagerhead
Posted on Thursday, October 27, 2016 - 12:26 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hello again, my back rest came in pieces and i am missing some hardware. Can someone please tell me the part numbers for these pieces. Hopefully i can still order them from Harley...

11,12,9,24,13,3,5



Top of pagePrevious messageNext messageBottom of page Link to this message

Rays
Posted on Thursday, October 27, 2016 - 05:00 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

3 -AA0406.11CXZB Screw (2) - 1/4-20 x 3/4 Torx truss hd., w/Scotch rip (bright zinc)
5 - AA0508.2CXZB Screw (2) - 5/16-18 X1.0 socket hd(bright zinc)
9 - C0075.1AK Pin
11 - C0091.AK Bearing (2)
12 - C0092.1AK Spring
13 - CA0018.02A8 Screw
24 - N0018.1AK Detent, Tail Rack

I added the description of the screws from the rear of the parts manual.
I'm sure there would a few of these parts gathering dust on shelves after various tail 'clean-ups'?
Top of pagePrevious messageNext messageBottom of page Link to this message

Electraglider_1997
Posted on Thursday, October 27, 2016 - 10:36 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I think it would great if the entire Uly could be presented like the above two posts. Exploded views and part numbers. How about it there Froggy?
Top of pagePrevious messageNext messageBottom of page Link to this message

Mark_weiss
Posted on Thursday, October 27, 2016 - 10:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So long as this diagram is up, which part needs to be removed in order to defeat the lock mechanism? Just the pin (9)?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hughlysses
Posted on Thursday, October 27, 2016 - 10:53 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

All the Buell models parts diagrams are accessible at Twin Motorcycle's site:

http://www.twinmotorcycles.com/webshop/searchparts .asp

The Buell part numbers are listed for each part in the list below the diagram. So you can either order the part from them, or take the part number to your local HD dealer and buy it there.
Top of pagePrevious messageNext messageBottom of page Link to this message

Electraglider_1997
Posted on Thursday, October 27, 2016 - 11:43 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks
Top of pagePrevious messageNext messageBottom of page Link to this message

Court
Posted on Thursday, October 27, 2016 - 12:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It's amazing to me . . . . as thrilled as I am that they did what Buell should have done. . . . that Twin Motorcycles takes documents that are marked COPYWRITED and replaces the information as if it were their information.

While I understand no one, at this point, is going to pursue copywriter violations, that's akin to me putting my name on Mark Twain's work.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Thursday, October 27, 2016 - 12:50 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm glad they support the brand, but they have played fast and loose with intellectual property for as long as I've been watching them.

I don't know what NL's IP laws look like.
Top of pagePrevious messageNext messageBottom of page Link to this message

Court
Posted on Thursday, October 27, 2016 - 12:52 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I'm on the same page. I am thrilled they are doing it, could care less about the laws, just personally miffed that someone would label someone else's work and property as their own.

No biggie . . . just different from the way I do things.
Top of pagePrevious messageNext messageBottom of page Link to this message

Lagerhead
Posted on Thursday, October 27, 2016 - 03:43 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks yall!
Top of pagePrevious messageNext messageBottom of page Link to this message

Ourdee
Posted on Thursday, October 27, 2016 - 07:51 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Court, I get it. Credit where credit's due. It is inside you or it isn't. I don't care who takes credit for my suggestions when the results fulfill my goals. I do think less of the Plagiarist though. It would be easy to credit the source.

I am thinking out loud here; Do copyrights have to be renewed every so often?
Top of pagePrevious messageNext messageBottom of page Link to this message

Court
Posted on Thursday, October 27, 2016 - 11:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

>>>Do copyrights have to be renewed every so often?

It kind of varies . . .

But, the salient issue, in this case is affixing another name. If a James Michener book has a copyright expire . . . I can't write By Court Canfield on the front and sell it.

It's not so much a big deal here and I am thrilled that Dris and company are doing all they are doing to support the brand. It's just a bit of an ethical detail that gives me, personally, pause.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Thursday, October 27, 2016 - 11:54 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

They bought 2 of my throttle shafts and then copied them and started selling them for twice as much. Nothing illegal but not what I consider kosher.
Top of pagePrevious messageNext messageBottom of page Link to this message

Natexlh1000
Posted on Friday, October 28, 2016 - 08:55 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If they were going to make their own anyways, why did they bother to buy a couple in the first place?
Surely, that could have just measured an OEM one as you had without paying you anything?

Perhaps they didn't anticipate how popular they would be?

That's F'ed up anyways.
Top of pagePrevious messageNext messageBottom of page Link to this message

Hughlysses
Posted on Friday, October 28, 2016 - 09:27 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Surely, that could have just measured an OEM one as you had without paying you anything?

Tootal's part is an improvement over the OEM part with a slot in the shaft for the butterfly rather than a flat being machined in the shaft. They actually copied his improved design.

Yea, that's kind of crummy.
Top of pagePrevious messageNext messageBottom of page Link to this message

Tootal
Posted on Friday, October 28, 2016 - 10:51 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

And while we're being honest, my design was taken from the design of both the Keihin CV Harley carburetors and also Weber Side Draft DCOE's. Both of which I have a lot of experience with. The design of the Buell vendor was for easy manufacturing. Cutting a flat is so easy compared to a slot.
Now both the Keihin and Weber are also cut flat do they don't block the air but I erred on the side of strength since not too many people were racing their Uly's!

Chad being one exception!
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration