G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through March 09, 2008 » Voltage Meter « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through February 25, 2008Bosh30 02-25-08  07:35 pm
Archive through February 13, 2008Jammin_joules30 02-13-08  11:24 pm
Archive through February 10, 2008Treadmarks30 02-10-08  09:20 am
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Court
Posted on Saturday, October 11, 2008 - 12:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Just did the FatVM . .. nice. I stuck about 4 more things on Henrik's bike today . . gotta know what's going on.

FtB. . . thanks for blazing the trail.

I'm curious to see who, at Buell, has the tiny finger to put the small nut, nearest the steering pivot, on.

I used a long extension magnet and some language I learned in the service.

I wanted to put silicon around the wires into the housing to seal them and didn't have any around. I cut a sponge type earplug in half, compressed it and stuffed it in the hole.

Great work FtB.

Court
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Saturday, October 11, 2008 - 12:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ben and I mocked up your relay delay (rev 2) on the breadboard last night. Appears to be working well, but I want to add some hysteresis so if it drops out it waits a few seconds to cut back in.
Top of pagePrevious messageNext messageBottom of page Link to this message

Court
Posted on Saturday, October 11, 2008 - 02:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

FtB . . . where did you connect the voltage monitor?

Bill: Henrik will be using this bike a lot so make it as perfect and as hysterical as possible.

: )

I tossed the PIAA wiring harnesses and made my own . . . damned impressive I might say!
Top of pagePrevious messageNext messageBottom of page Link to this message

Nillaice
Posted on Wednesday, March 20, 2013 - 10:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)



(Message edited by nillaice on March 21, 2013)
Top of pagePrevious messageNext messageBottom of page Link to this message

Nillaice
Posted on Thursday, March 21, 2013 - 05:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

yes, i'm posting in a thread that has been in a coma for the last 5 years. but this thread is friggin great an is very searchable. it seems to be the origional thread that others will refernce, so maybe my post will help some body out.

i ordered mine from ebay. signal dynamics still has them on thier site, but they charge a few bucks for shipping. i followed Ft B's pic-strucions and only have some enhancements to contribute.
~ stick the box about an half inch from the port on the back of the IC, not right next to it as pictured. i had some interference with the conrtoll switch wiring.
~ you can take the IC out of the module with the bottom gromet and nut still attached. that 5/16 nut is hard to reach, but IS doable with a magnet and 'words of encouregement' as previosly mentioned.

other than that i soldered the wires into the back of the plug for the 12v outlet. red to red, black to black and yellow.
pretty slick, i know.

of course i had to re-solder it cuz the wires need to be routed and soldered with everything installed


it looks fatory-esque .... and nobody will ever see it
Top of pagePrevious messageNext messageBottom of page Link to this message

Froggy
Posted on Thursday, March 21, 2013 - 05:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration