G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » EBR Forum » EBR Race ECM & Exhaust Tip Instructions « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Needforspeed
Posted on Tuesday, February 09, 2016 - 04:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I was able to purchase the EBR 1190RX Exhaust tips and ECM combo. It use to come with instruction from EBR. There are no instructions with it just the hardware from EBR (LAP). I assume it will be the same as the 1125R instructions; however, I would like to see them. Does anyone have a copy they can post or email me with? Was there anything but the tips and ECM? Bolts or clamps?
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Tuesday, February 09, 2016 - 05:10 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

No instructions with mine either but ECM is under the seat and TPS reset is same as 1125.

Make sure tips go all the way down inside the sleeve and the clamps needs to be tighter than you think..
Top of pagePrevious messageNext messageBottom of page Link to this message

Ursus
Posted on Tuesday, February 09, 2016 - 06:55 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ECM Replacement Procedure
When replacing the ECM on all 2014 EBR 1190 models, the following steps must be followed to ensure
the bike will run properly after the new ECM installed on the bike:
1) Clear fault codes
1". The replacement ECM may contain incidental historic fault codes that are logged
due to the initial ECM configuration process. Clear these codes using the
instrument cluster before performing the TPS reset using the following
procedures:
a. Turn the ignition switch on.
b. Press the top button on the instrument cluster to access the "Menu".
c. Scroll to "Diagnostics" and select.
d. Scroll to "Historic Faults" and select.
e. Scroll to "Clear Faults" and select.
f. Scroll to "Yes" and select.
g. Exit menu.
2) TPS reset
1. Turn the key on and make sure the handlebar kill switch is in the run position.
2. Do not start the bike.
3. Turn throttle to full open and hold about one second.
4. Release throttle completely so it snaps shut. Wait one second.
5. Repeat the steps 3 and 4 (full throttle, hold, and release) two more times.
6. Turn the key off for at least two seconds.
7. Turn the ignition key on and start the bike.
3) IAC averaging reset
1.. After completing the TPS reset procedure, leave the bike running and allow it to
warm to operating temperature before riding. This process will allow the IAC to reset properly.
Top of pagePrevious messageNext messageBottom of page Link to this message

Needforspeed
Posted on Tuesday, March 01, 2016 - 05:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

@Ursus, Thanks so much for the procedures. I should be doing the ECM swap this week if all goes well. WV has changed the rules around exhaust noise so I am working through that to be sure I will be OK.
Top of pagePrevious messageNext messageBottom of page Link to this message

Mike13
Posted on Tuesday, March 01, 2016 - 06:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I think you should be ok as far as noise. I have the same set up on mine and it is not much louder then stock, just a lil deeper tone. Wish it was a lil bit louder but I'm getting use to the idea of being a lil more stealthier these days.
Top of pagePrevious messageNext messageBottom of page Link to this message

Terrys1980
Posted on Wednesday, March 02, 2016 - 09:35 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

It gets loud when you get those RPMs up but you don't realize because you have a helmet on.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ourdee
Posted on Friday, March 11, 2016 - 09:24 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Stealth is smart.



The loud guy is your Rubber Duck, what'd ya think R.D. stood for?


« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration