G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Quick Board Archives » Archive 0212 (December 2002) » Technical » 02 lightning ECM changeout « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Mfell2112
Posted on Sunday, April 28, 2002 - 06:03 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Two questions for anyone who has changed out the Eletronic Control Module on a lightning (02)

1. When installing a "new" module the manual calls for the throttle position switch (TPS) to be re-calibrated via the Harley Scanalyzer. An expensive item that I do not own. If installing the new unit how far off will the zeroed (idle) position be off? Will the full throttle positon also be out?

2. If finding that the "new" module does infact need calibration can I reinstall the original? Does it keep the already known settings? My belief with other types of systems the answer should be yes, but I'm not sure. If a battery were changed out one would hope I do not require a re-cal of the ECM each time!

Thanks

mike
Top of pagePrevious messageNext messageBottom of page Link to this message

Rempss
Posted on Sunday, April 28, 2002 - 10:39 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Mike,

You need to have a Buell dealer reset the TPS anytime a new ECM is put in or TPS is removed/replaced.

It will be off somewhere from zero to one million depending on how lucky you are. The signal is a changing value from about .5 - 5.0, if its off at idle it's off in the whole range.

You should be OK to ride a short while (to the dealer) without a reset, although you will not know the full potential of your bike unless the TPS is reset in cases mentioned above. Though some have not been able to keep their bikes running without an immediate service, most just experience poor performance until done.

You can reinstall the prior ECM without a service as long as the TPS has not been moved from the last location the ECM knew. The battery can be removed without regard for the setting it is "flashed" into the memory.

What other mods are you doing? Do tell.

Jeff
Top of pagePrevious messageNext messageBottom of page Link to this message

X1glider
Posted on Monday, April 29, 2002 - 02:40 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Jeff, good to know a dead battery won't require a reset. I haven't read this section in the service manual yet. Are there other places you are getting your information about the ECM? I'm wanting to know more even though I don't plan on changing it for a while. I'm going to work on the suspension and steering first. I thing handling should come first since I commute with it.
Top of pagePrevious messageNext messageBottom of page Link to this message

Milleniumx1
Posted on Friday, May 07, 2004 - 12:45 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

You'll have to get that TPS reset to make sure your bike is running correctly after the race ECM install. I put mine on in my garage, and then took it out and rode it. I didn't really get on it much since I knew the TPS wasn't yet redone. I could tell the bike felt better over the factory unit. But once I got the TPS reset (I rode it to the dealer, 12 miles), WOW - what a difference.

Mike M
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration