G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through August 16, 2004 » Clutch Cover Bolt-Head Burred! « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ozzyxb9r
Posted on Sunday, August 15, 2004 - 04:59 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

hi there,

i went to do a trans oil change and burred head of one of the allen key type bolts that hold the clutch cover on...whats the best way to remove the burred bolt?

cheers

morgan
Top of pagePrevious messageNext messageBottom of page Link to this message

Shawn_9r
Posted on Sunday, August 15, 2004 - 05:06 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Morgan, when you say burred? Do you mean striped? If so you can get left handed drill bit/screw extractor and it should come right out.
Top of pagePrevious messageNext messageBottom of page Link to this message

Coldwthrrider
Posted on Sunday, August 15, 2004 - 08:44 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Two of the three stupid torx screws holding the primary cover on stripped because the previous owner over tightened them. I had to drill them out (carefully!) and there was plenty of shaft length to grab with a vise grips to back the threads out. The HD dealer has hex head replacements for those (or a hardware store maybe). Watch the torque specs and use them!
Top of pagePrevious messageNext messageBottom of page Link to this message

Blake
Posted on Sunday, August 15, 2004 - 01:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

When removing those fasteners, it is important to first break loose each one (maybe 1/8th turn) before then fully removing them. Removing one fastener while leaving the others still fully tightened will put the others in a serious bind and lead to stripping the head of the screws.

For next time. : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Ozzyxb9r
Posted on Sunday, August 15, 2004 - 06:23 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ive stripped the head of the screw, so i need a screw extractor?
Top of pagePrevious messageNext messageBottom of page Link to this message

Dbenjami
Posted on Sunday, August 15, 2004 - 06:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Yea, i just removed one today with a screw extractor... pretty easy job...
Top of pagePrevious messageNext messageBottom of page Link to this message

Awprior
Posted on Sunday, August 15, 2004 - 07:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I had the same problem with my M2, I'm not sure if this fix will work for your bike or not. I replaced the torx fasteners with a few 1/4-20 3/4" socket head capscrews, with a few washers behind them to space them out correctly. I trust them much more than the torx fasteners. You can either use a screw extractor (a really small one, they're sometimes tough to get into a screw that small), or you can try to notch a side of the fastener and use a screwdriver and hammer to carefully spin it out. This is what I had to do with mine, those fasteners are really hard.

This is what I have done on my bike now, mind the little bit of rust on the capscrews, my bike isn't exactly a garage queen...

Top of pagePrevious messageNext messageBottom of page Link to this message

Al_lighton
Posted on Sunday, August 15, 2004 - 10:05 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

FYI, 1/4-20 Pan head (Allen) screws in stainless are a Home depot stock item.

Al
Top of pagePrevious messageNext messageBottom of page Link to this message

Awprior
Posted on Sunday, August 15, 2004 - 10:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I couldn't find the stainless ones and was in a pinch... Thanks for the heads up, Al.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Monday, August 16, 2004 - 09:15 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

You probably won't need the easy out, just drill off the head, and lift the cover over it, there will probably be enough left of the bolt for a pair of vice grips.
Top of pagePrevious messageNext messageBottom of page Link to this message

Freyke
Posted on Monday, August 16, 2004 - 09:37 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Get your but to your nearest "Big Box" store (Wal-Mart, Lowes, Home-Depot, Sears, etc) and pick yourself up a Black & Decker Screw Extractor Set PN/16270.... Works like a champ!... I got mine at Home Depot...
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration