G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Archive through August 09, 2010 » Boom Boom WHACK « Previous Next »

  Thread Last Poster Posts Pages Last Post
Archive through July 23, 2010Buell_4130 07-23-10  05:11 pm
         

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Wheelybueller
Posted on Friday, July 23, 2010 - 07:32 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

+1 Hootowl
I had a speed sensor beat me up for a while,it was a no run issue.
It feeds off the same low voltage line from the ecm to many other things.....
Top of pagePrevious messageNext messageBottom of page Link to this message

Kowpow225
Posted on Sunday, July 25, 2010 - 02:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Keep us updated on what the shop finds. Good luck.
Top of pagePrevious messageNext messageBottom of page Link to this message

Buell_41
Posted on Monday, July 26, 2010 - 11:09 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So I put everything back together in preparation to trailer her over to the shop. On a whim I fired her up but could not re-create problem... Really makes me uneasy to think I fixed the problem by dis-assmbling and re-assembling things. Anyone think the shop will be able to shed new light on what the problem really is/was?
Top of pagePrevious messageNext messageBottom of page Link to this message

Brumbear
Posted on Monday, July 26, 2010 - 08:38 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

no
Top of pagePrevious messageNext messageBottom of page Link to this message

Greg_e
Posted on Monday, July 26, 2010 - 09:37 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Not without costing a huge amount of money.
Top of pagePrevious messageNext messageBottom of page Link to this message

Etennuly
Posted on Monday, July 26, 2010 - 11:14 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Check and wiggle test your ignition switch plug. Some ign switches have failed causing these kind of problems, beyond that check the kill switch and start switch, pop the cover look for worn wires or rubbing.

Next up could be your fuel pump wiring and filters.
Top of pagePrevious messageNext messageBottom of page Link to this message

Ochoa0042
Posted on Tuesday, July 27, 2010 - 12:08 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

are you positive its not your relay? my bikes was doing the same thing a couple weeks ago, the ignition relay it was..
Top of pagePrevious messageNext messageBottom of page Link to this message

Buell_41
Posted on Tuesday, July 27, 2010 - 07:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Ok, I've queryed the ECM multiple times and haven't ever gotten codes. Today, it decided to give me some... tons actually...

Byte 2:94
23 - front injector short to ground or open
23 - battery voltage too low
15 - intake air sensor shorted to supply voltage or open

Byte 3:14
33 - fuel pump short to grond or open
33 - rear injector short to ground or open

Byte 4:80
44 - BAS short to ground or open

Byte 5:05
21 - active muffler control

So two things:
(1) I know it can't be all these at once so what do they all share
(2) I have no check engine light

There are two large plugs that connect to the ECM. But there's a smaller gauge wire that goes between them. What does that do?
Top of pagePrevious messageNext messageBottom of page Link to this message

Brumbear
Posted on Tuesday, July 27, 2010 - 10:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

did you have the bike running when you were switching the fuses?
Top of pagePrevious messageNext messageBottom of page Link to this message

Buellboy492
Posted on Tuesday, July 27, 2010 - 10:58 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Whenever I have "fixed" an electrical problem by taking it apart and putting it back together, I have attributed it to a bad ground. It happens to me. But I am FAR from any kind of trained mechanic. Or even a good maintainer...
Top of pagePrevious messageNext messageBottom of page Link to this message

Buell_41
Posted on Wednesday, July 28, 2010 - 06:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

cleared all those codes, took a quick jaunt down the lane and vwala! At least I know what it is now.


Cam Sync Failure


Thanks for all the help guys!
Top of pagePrevious messageNext messageBottom of page Link to this message

Buelltroll
Posted on Wednesday, July 28, 2010 - 08:16 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

So instead of me wading through 2 pages of not it, What WAS it? Guess I could have read a COUPLE posts up : p What caused all those codes though? LOL guess I could have read the ANSWER POST TOO my bad : D

(Message edited by buelltroll on July 28, 2010)

(Message edited by buelltroll on July 28, 2010)
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration