G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through July 04, 2009 » 9 pistons in a 12? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Ttags
Posted on Monday, June 29, 2009 - 10:33 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

ok, so our compression ratios are pathetic. if i throw the 9 pistons in my motor i'll be somewhre in the range of 11.25 : 1. Questions being, have many people done this? reliability issues ? and most of all, fuel maps, timing maps??? appreciate the help. winter is coming soon! would love to persue this project!
Top of pagePrevious messageNext messageBottom of page Link to this message

Xb9ser
Posted on Monday, June 29, 2009 - 10:41 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Compression ratio is 10 to 1. I think with 9 pistons in a 12 it is more like 12 1/2 to 1. Unleaded race gas only.
Top of pagePrevious messageNext messageBottom of page Link to this message

Xl_cheese
Posted on Tuesday, June 30, 2009 - 11:50 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've hear the 9 pistons bring it up to 11.5:1.

Of course it's all hearsay. I have a set of 9 pistons sitting on my bench. : )
Top of pagePrevious messageNext messageBottom of page Link to this message

Fast1075
Posted on Tuesday, June 30, 2009 - 12:06 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Be advised that proper setup and tuning is required or it will detonate its self to pieces....that is a LOT of compression in a street motor...it has been done...and with success...use VERY good fuel.
Top of pagePrevious messageNext messageBottom of page Link to this message

Steve_mackay
Posted on Tuesday, June 30, 2009 - 12:44 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Unleaded race gas only.

Bud at Hals is runing on normal 93 octane pump gas with 9 pistons in a 12 with a daytona twin tech without issues.}
Top of pagePrevious messageNext messageBottom of page Link to this message

Hogs
Posted on Tuesday, June 30, 2009 - 12:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I think it works out to 12.3:1 But When I do it, Having another set of 9 cyls. and pistons complete to put in my 12, I think I will CC the heads and in doing so will lower the compression down to 11.5:1 or perhaps 11.25:1..
Btw this Twin tech unit is that not similar to them old T.Boxes that were an add on, or What else do they compare to?

And yeah good gas is a must...

(Message edited by hogs on June 30, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Hr_puffinstuff
Posted on Tuesday, June 30, 2009 - 01:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

the lead is for the valves, not the compression
Top of pagePrevious messageNext messageBottom of page Link to this message

Xoptimizedrsx
Posted on Tuesday, June 30, 2009 - 03:08 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

its a actual 12.34:1 on my bike i built. read the cc fill after that. it drops.
run the zero base and .030 head you drop to the cc less than 1203. mine is aprox 1170/1180 now set up this way.

the fuel will need to be 91 min but race fuel is better. if your running a o2 sensor system run unleaded only.

sonoco 260gtplus or mrpro4.1 vp fuel is best there are others in each of those brands to use.

the vp rep. emailed me and said to use the m109 or the mrpro fuel with the afr set at 13.43 if possible. but use unleaded only.

before you button it up check the exhaust valve min clearance. i dont like below .95 squish. i triple checked this value with a few known places who race.

be sure to let the tapits bleed off then turn the motor over to check the squish.

over all a good cheap upgrade on pump gas.

dyno said the fuel was just fine as it sat. tuning will help.

(Message edited by on July 03, 2009)
Top of pagePrevious messageNext messageBottom of page Link to this message

Hogs
Posted on Tuesday, June 30, 2009 - 03:13 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thanks MIke...
Top of pagePrevious messageNext messageBottom of page Link to this message

Jdemoxb9r
Posted on Tuesday, June 30, 2009 - 06:21 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

winter is coming soon!

NOOOOO!!!! oh wait its only July.....Scared me for a minute
Top of pagePrevious messageNext messageBottom of page Link to this message

Ttags
Posted on Wednesday, July 01, 2009 - 08:25 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

alright... thanks... how bout another piston combo? i wanna be around 11:1... any ideas? or should i have a machine shop shave the top of the 9 pistons?
Top of pagePrevious messageNext messageBottom of page Link to this message

Hogs
Posted on Wednesday, July 01, 2009 - 08:35 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Check the on line sponsors within ,If ya want some Nice Forged units etc... Yeah you could do that,But they would really have to know their Stuff...,also dig out the Combustion areas abit cc them, thicker head and base gaskets and better quality gaskets...

Don`t think ya would have to do much to get em around 11 or 11.25 or so
Top of pagePrevious messageNext messageBottom of page Link to this message

Tattoo72
Posted on Wednesday, July 01, 2009 - 09:02 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Great guys and they are sponsors here. They will machine the pistons to what ever compression ratio you want. http://www.jetroadracing.com/racing_pages/parts/bu ell_engine_parts.html
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration