G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through February 04, 2008 » Wiseco Pistons « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Schmitty
Posted on Sunday, February 03, 2008 - 12:11 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I also posted this in the Knowledge Vault, so don't flame me too bad!

I am going to change the oil pump drive gear to the bronze gear on my XB9R race bike. While I'm at it I'm going to do a top end inspection. The bike has 5500 miles on it. I was thinking about dropping in a set of Wiseco forged piston and Wiseco rings in the standard bore. Is there any benefit to this with the standard bore? I don't have the cash to go big bore, but I'm adding the Micron full system, and having the bike dyno tuned. What is the standard compression ration for an XB9? The Wiseco catalog says 10:1 with their pistons and rings installed. They also claim the usual reduced friction and stronger, etc.. There is also a .010" over option. Is this for worn cylinders? Would 5500 miles have worn the cylinders that bad? Any help or knowledge is appreciated.

Schmitty
Top of pagePrevious messageNext messageBottom of page Link to this message

Badlionsfan
Posted on Sunday, February 03, 2008 - 12:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

.010 over is for worn cylinders. 5500 miles is barely broke in, should be fine.

stock is 10.0 to 1, so no advantage there.

not sure what pistons have to do with friction. if your pistons are touching the cylinder walls, you got issues.

unless you're planing on nitrous or something, leave it alone.
Top of pagePrevious messageNext messageBottom of page Link to this message

Björne666
Posted on Sunday, February 03, 2008 - 01:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Take the money you planned to buy pistons for a get a head job done. Same compression pistons will not add ponies in the stable, but better flowing heads will. :-)
Top of pagePrevious messageNext messageBottom of page Link to this message

Jackbequick
Posted on Sunday, February 03, 2008 - 11:17 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Pistons that are .010 over will normally require cylinder re-boring to get them to fit.

At 5,500 miles you should be fine with a new set of rings.

But measuring the cylinders and pistons after your get it torn down will really help a lot on deciding it all.

Jack
Top of pagePrevious messageNext messageBottom of page Link to this message

Badlionsfan
Posted on Monday, February 04, 2008 - 12:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

why on earth would he even need a ring change at 5500 miles? it's barely broken in?
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Monday, February 04, 2008 - 01:00 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Wiseco has .010" over pistons?
Top of pagePrevious messageNext messageBottom of page Link to this message

Badlionsfan
Posted on Monday, February 04, 2008 - 01:18 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

yup.
http://www.wiseco.com/PDFs/Catalogs/2008/VT/Buell. pdf
Top of pagePrevious messageNext messageBottom of page Link to this message

Jackbequick
Posted on Monday, February 04, 2008 - 11:02 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I mentioned the ring change because it is a race bike. It is common on some race engines to do a hone and ring replacement whenever the engine is torn down.

But the are a lot of factors to consider. Like the measured wear, if any, on cylinder and piston, the appearance of the cylinder (original cross hatch honing marks all gone, etc.), the amount of time it takes to get the rings in broken in/sealing well after reassembly, etc.

Schmitty,

Just out of curiosity, do you run that on synthetics? Or break it in on regular oil and switch to synthetics? Some engines break in better on dinosaur oil than they do with the reduced friction of synthetics.

Jack
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration