G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » XBoard » Buell XBoard Archives » Archive through September 23, 2007 » Reset new odometer?? « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Xbrlaredo
Posted on Friday, September 21, 2007 - 06:31 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Hi,how can i put my 6300 real miles of my XBR9 firebolt on my Ebay used odometer with 830 m. in it? Any HD'service do it?
Thanks
Paul
Top of pagePrevious messageNext messageBottom of page Link to this message

M1combat
Posted on Friday, September 21, 2007 - 07:18 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Push it around in circles for a while : ).
Top of pagePrevious messageNext messageBottom of page Link to this message

Lost_in_ohio
Posted on Friday, September 21, 2007 - 07:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Put it on and don't worry about it. There is a place on the title that says odometer not accurate. Well at least here in ohio.
Top of pagePrevious messageNext messageBottom of page Link to this message

Punkid8888
Posted on Friday, September 21, 2007 - 07:27 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

just do burn outs way more fun
Top of pagePrevious messageNext messageBottom of page Link to this message

Teeps
Posted on Friday, September 21, 2007 - 07:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Try Palo Alto Speedo shop.

http://www.paspeedo.com/

They set mileage on a Honda motorcyce odo for a friend; don't know why they can't for a Buell.
Give them a call.
Top of pagePrevious messageNext messageBottom of page Link to this message

Interex2050
Posted on Friday, September 21, 2007 - 07:49 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have wanted to try this out for a while now...

1) using an oscilloscope find out what the speedo sensor is sending out...
I am assuming it is probably some sort of hall sensor thus it sends out pulses with the frequency determining the "speed".
Primarily watch the voltage and the wave form...

2) using a power supply, power up the speedometer

3) then using a signal generator emulate the pulse that the speedometer sensor puts out...
and connect the signal to the speedometer sensor pin on the back of the speedometer
You can play around with the frequency to get it to climb as fast as you need it to...
I have a feeling though that it will not pick up frequencies above a certain range.

4) last step would be to watch the odometer to make sure you do not go over if you do you will need to cycle the odometer...

And there you go that should do it...

Although this is all theoretical, and I have not had a chance to actually test this.
But I do not see why it would not work.
Top of pagePrevious messageNext messageBottom of page Link to this message

Jackbequick
Posted on Saturday, September 22, 2007 - 08:13 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have a Dakota Digital speedo on my Dyna and can set a value in the calibration mode to correct speedometer readings. Dakota also sells a device for correcting both speed and odometer reading on their instruments. You can see the details on that here:

http://www.dakotadigital.com/index.cfm/page/ptype= results/Category_ID=115/home_id=60/mode=cat/cat115 .htm

Dakota offers the calibration devices for H-D, Honda, and a generic version too. I'm thinking it can't be too complicated to do it yourself.

My son works on marine electronics and has done something like that to set the engine hour meters on boats to the proper value. This is on Yanmar diesels that output a timing "tick" at a known frequency when running.

He does it by using a signal generator where he can select the type of signal that is output and the level of the output. I don't know the specifics beyond that but can probably get more info about it. By changing the frequency, he can make it count up the hours quickly.

If you can get a "techhie" involved and have him monitor the output signal from the speedo with an oscilloscope he can determine the output level of the speedo ticks.

Jack

(Message edited by jackbequick on September 22, 2007)

(Message edited by jackbequick on September 22, 2007)
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a public posting area. Enter your username and password if you have an account. Otherwise, enter your full name as your username and leave the password blank. Your e-mail address is optional.
Password:
E-mail:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration