G oog le BadWeB | Login/out | Topics | Search | Custodians | Register | Edit Profile

Buell Forum » Big, Bad & Dirty (Buell XB12X Ulysses Adventure Board) » BB&D Archives » Archive through September 08, 2011 » Helicoil question... « Previous Next »

Author Message
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Sunday, August 21, 2011 - 01:22 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Long story short, I stripped the drain hole on the swingarm a while back. I avoided doing a Timesert due to idiocy and false economy logic. Ultimately, I 'fixed' the issue w/ a 5/8" Helicoil and matching bolt, torqued to 30 ft-lbs using teflon tape, a plug washer and a crush washer.

Problem is, it still weeps oil. Not much, but I would prefer it be oiltight.

Any suggestions(short of replacing the swingarm) for buttoning this up? Is a Timesert still an option seeing how far I have opened up the drain hole?
Top of pagePrevious messageNext messageBottom of page Link to this message

Teeps
Posted on Sunday, August 21, 2011 - 06:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

First, is the heli-coil flush with the sealing surface? If not; you'll likely never to get it to fully seal.

Give this a try:
Remove the plug and clean it and the heli-coil threads.

Apply PERMATEX 59235 high temperature thread sealant to the plug threads, top to bottom all the way around.
Not sure what a plug washer is; but a single crush washer should be all you need.

I never torque the drain plug over 12lbs/ft.
Top of pagePrevious messageNext messageBottom of page Link to this message

Reepicheep
Posted on Sunday, August 21, 2011 - 09:47 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Find the other post here (in the last few days) where somebody posted a nice picture of what is effectively a bolt in a bolt.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skinstains
Posted on Monday, August 22, 2011 - 12:32 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

30 ft/lb is waaayyyyy to tight. The aluminum is pretty thick where the drain is so you could just tap it with an interference fit like a pipe thread. I personaly wouldn't go anywhere near my engine's oil supply with permatex.
Top of pagePrevious messageNext messageBottom of page Link to this message

Teeps
Posted on Monday, August 22, 2011 - 11:25 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Skinstains Posted on Monday, August 22, 2011
I personaly wouldn't go anywhere near my engine's oil supply with permatex.



Pg. 1-14 step 2 in the '06 Uly service manual says to apply Loctite 565 thread sealant to the drain bolt. The Permatex is equivalent.

But, in the same sentence they do say to torque the bolt to 29~34lbs/ft.
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Tuesday, August 23, 2011 - 09:31 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Teeps-

I assume the thread sealer can be had at any auto parts store? I already have Loctite, I'll check to see if its the correct type.

The reason I have it torqued to 30 ft-lbs is because there is a helicoil insert in there, providing more strength than the bare aluminum, and because at my normal 22 ft-lbs, it dripped quite a bit. I progressively increased the torque value by 1 until I was satisfied.
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Tuesday, August 23, 2011 - 09:33 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

And just to be clear, unless I have to, I am NOT looking to re-tap the hole again. It is already at 5/8, which is quite a bit larger than the original 1/2.
Top of pagePrevious messageNext messageBottom of page Link to this message

Teeps
Posted on Tuesday, August 23, 2011 - 06:45 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I believe I bought it at Pep Boys.
Could have been the Harley dealer too.
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Thursday, August 25, 2011 - 01:25 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thx, Teeps.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skinstains
Posted on Saturday, August 27, 2011 - 11:29 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

None of my bikes leak from the drainplug and I never use threadlocker, be it Permatex or Locktite. I also would never torque them to 30 ft/lb. Torqueing that plug to 29-34 ft./lbs. is what got that thing to leaking in the first place.
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Sunday, August 28, 2011 - 11:40 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

'Torqueing that plug to 29-34 ft./lbs. is what got that thing to leaking in the first place.'

Actually, no. The original plug hole stripped after torquing it to 27 ft-lbs, which had been my habit for 33k miles. After my helicoil insert, I BEGAN at 15 ft-lbs trying to be safe. The plug flowed like a broken nose, and basically ruined my rear brake pads. I gradually increased the torque value and ran the bike until the weep was at an acceptable level.
Top of pagePrevious messageNext messageBottom of page Link to this message

Rwcfrank
Posted on Sunday, August 28, 2011 - 12:09 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I have to assume that the leak is coming from the area between the outside of the Helicoil and the inside of the hole in the swingarm and its not going to get better by tightening other than you may be compressing the o ring enough to stem the flow.If the Helicoil is flush with the swingarm try a flat compression washer of rubber or plastic or a stato-seal. If its not flush you may be able to hit it with a file to bring it flush.
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Sunday, August 28, 2011 - 02:28 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thx, Rwc. I had been thinking that, during my hatchet job, I misaligned the hole just enough to not allow the bolt shoulder to tighten flush with the swingarm.

Would a timesert insert work with the helicoil threads I already have?

Where can I get a Stat-o-seal?

(Message edited by portero72 on August 28, 2011)
Top of pagePrevious messageNext messageBottom of page Link to this message

Skinstains
Posted on Sunday, August 28, 2011 - 04:13 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Sorry, but I think 27 ft/lb is too much as well. It's a steel thread going in to an aluminum thread and I think that it is a typo in the book and that that is the root of this problem. For what it's worth...used swingarms are really cheap on Feebay.
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Sunday, August 28, 2011 - 04:20 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

I've been keeping an eye on Fleabay for used swingarms, not seen one recently. I may pick one up just as insurance.
Top of pagePrevious messageNext messageBottom of page Link to this message

Skinstains
Posted on Sunday, August 28, 2011 - 04:26 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

If you can't find one let me know as I may have an extra one hanging around somewhere. Look in to the drain plug torque thing too, I think that there was a real deal typo on both the primary and swingarm plugs. For some reason 13 ft/lb sticks out in my memory.
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Sunday, August 28, 2011 - 10:15 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thx, Skins. I may take you up on that. There are a bunch on ebay, but they are all for tubers or the smaller XB's. Boo.
Top of pagePrevious messageNext messageBottom of page Link to this message

Electraglider_1997
Posted on Monday, August 29, 2011 - 10:36 am:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

stat-o-seal
http://www.allsealsinc.com/statoseals.html
Top of pagePrevious messageNext messageBottom of page Link to this message

Prowler
Posted on Monday, August 29, 2011 - 12:53 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

"I misaligned the hole just enough to not allow the bolt shoulder to tighten flush with the swingarm"

If this is the case, and you want to save the heli-coil that's in there already, you really should go to a heavy rubber (or better yet, nylon/urethane) oil drain plug washer to make up the difference in the mis-alignment between your plug and the machined surface of the swingarm. Ace Hardware usually has them in many sizes in boxes in the hardware department. You should only have to torque the plug to about 10-15 ft/lbs to obtain a seal. This should solve your leaking problem. But make sure you replace the washer every time you change your oil. 30 ft/lbs of torque is too much for this plug (it's still working the heli-coil threads against the Aluminum casting of your swingarm.....not good).
Top of pagePrevious messageNext messageBottom of page Link to this message

Portero72
Posted on Monday, August 29, 2011 - 05:01 pm:   Edit Post Delete Post View Post/Check IP Print Post    Move Post (Custodian/Admin Only) Ban Poster IP (Custodian/Admin only)

Thx, Prowler, that is a good suggestion.
« Previous Next »

Add Your Message Here
Post:
Bold text Italics Underline Create a hyperlink Insert a clipart image

Username: Posting Information:
This is a private posting area. Only registered users and custodians may post messages here.
Password:
Options: Post as "Anonymous" (Valid reason required. Abusers will be exposed. If unsure, ask.)
Enable HTML code in message
Automatically activate URLs in message
Action:

Topics | Last Day | Tree View | Search | User List | Help/Instructions | Rules | Program Credits Administration